Black & Decker FS110L instruction manual Additional Safety Rules for the Laser, Power Connections

Page 5

ADDITIONAL SAFETY RULES FOR THE LASER

For your convenience and safety the

FOR LASER SAFETY OBSERVE THE FOLLOWING:

following labels are on your tool.

 

Fig. A

Fig. B

•LASER LIGHT - DO NOT STARE INTO BEAM, APERTURE, or into a reflection from a mirror-like surface Fig. A & B.

•AVOID EXPOSURE - LASER LIGHT IS EMITTED FROM FRONT GUARD APERTURE. Use of controls or adjustments, or performance of procedures other than those specified herein may result in hazardous laser light exposure.

•DO NOT DISASSEMBLE LASER MODULE. The laser is a CLASS II LASER PRODUCT that can emit laser power up to 1 mW MAX at 650 nm, which could result in exposure with the module disassembled. The laser unit complies with 21 CFR 1040.10 and 1040.11.

•USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

•THE USE OF OPTICAL INSTRUMENTS with this product will increase eye hazard.

•LASER RADIATION, avoid direct eye exposure, serious eye injury can result.

•DO NOT OPERATE IN EXPLOSIVE ATMOSPHERES, such as in the presence of flammable liquids, gases, or dust.

•USE ONLY WITH THE SPECIFICALLY DESIGNATED BATTERIES. Use of any other batteries may create a risk of fire.

•USE ONLY ACCESSORIES that are recommended by the manufacturer for your model.

•ACCESSORIES THAT MAY BE SUITABLE FOR ONE LASER, may create a risk of injury when used on another laser.

•REPAIRS AND SERVICING MUST be performed by a qualified repair facility. Repairs performed by unqualified personnel could result in serious injury.

•DO NOT REMOVE OR DEFACE WARNING LABELS. Removing labels increases the risk of exposure to radiation.

•THIS PRODUCT IS INTENDED for use in a temperature range of 41°F(5°C) - 104°F(40°C).

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the machine to the power line, make sure the switch is in the “OFF” position and be sure that the electric current is of the same characteristics as indicated on the machine. All line connections should make good contact. Running on low voltage will damage the machine.

DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

MOTOR SPECIFICATIONS

Your machine is wired for 120 volt, 60 HZ alternating current. Before connecting the machine to the power source, make sure the switch is in the “OFF” position.

GROUNDING INSTRUCTIONS

THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK.

1. All grounded, cord-connected machines:

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This machine is equipped with an electric cord having an equipment- grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the

equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the machine is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that accept the machine’s plug, as shown in Fig. C. Repair or replace damaged or worn cord immediately.

2.Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less than 150 volts:

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Before Returning this Product for ANY Reason Please Call FS110L 10 Compound Laser Miter SAWImportant Safety Instructions Safety Guidelines DefinitionsGeneral Safety Rules Stay ALERT, Watch What YOU are Doing Failure to Follow These Rules MAY Result in Serious Injury Additional Safety Rules for Miter SawsPower Connections Additional Safety Rules for the LaserMotor Specifications Grounding InstructionsExtension Cords Unpacking and CleaningFunctional Description ForewordAssembly Carton ContentsAttaching Dust BAG Operating Controls and AdjustmentsFastening Machine to Supporting Surface Table Hazard AreaRotating the Table for Miter Cutting Locking the Switch in the OFF PositionStarting and Stopping the Miter SAW Pointer and Scale Disconnect the Machine from Power SourceLocking Cuttinghead in the Down Position Tilting Cuttinghead for Bevel CuttingSide Supports Adjusting Sliding FenceRear STABILIZER/CARRYING Handle Adjusting Downward Travel of SAW Blade Adjusting Blade Parallel to Table SlotAdjusting 90 and 45 Bevel Stops Disconnect Machine from Power SourceAdjusting Sliding FIT Between Cuttinghead ARM and Trunnion Adjusting Tension of Cuttinghead Return SpringAdjusting the Lower Blade Guard Laser USE and AdjustmentHOW to Check Laser Alignment HOW the Laser WorksTo Check for Vertical Alignment To SET Kerf AdjustmentLaser Maintenance General Cutting Operations Typical Operations and Helpful HintsAuxiliary Wood Fence Right Wrong Cutting AluminumCutting Bowed Material Cutting Crown Molding Crown MoldingChanging the Blade MaintenanceBrush Inspection Replacement Trouble Shooting Guide Mode D’EMPLOI Directives DE Sécurité Importantes Lignes Directrices EN Matière DE Sécurité DéfinitionsRègles Générales DE Sécurité Page Conserver CES Directives Connexions Électriques Règles DE Sécurité Supplémentaires Pour LE LaserCaractéristiques Techniques DU Moteur Directives DE Mise À LA TerreDésemballage ET Nettoyage Rallonges ÉlectriquesDescription Fonctionnelle Utilisation DES Contrôle ET Réglages Contenu DU CartonAssemblage Verrouillage DE Linterrupteur EN Position Darrêt Démarrage ET Arrêt DE LA Scie À OngletsRotation DE LA Table Pour Effectuer UNE Coupe À Onglet Pointeur ET ÉchelleStabilisateur ARRIÈRE/POIGNÉE DE Transport Réglage DU Guide CoulissantSupports Latéraux Ajustement DE LA Lame Parralèle À LA Fente DE LA TableRéglage DU PROTÈGE-LAME Inférieur Utilisation ET Réglage DU LaserFonctionnement DU Laser Vérification DE L’ALIGNEMENT DU LaserVérification DE L’ALIGNEMENT Vertical Opérations Courantes ET Conseils UtilesRéglage DU Trait DE Scie Entretien DU LaserCoupe Daluminium Opérations DE Coupe GénéralesCoupe DE Matériau Arqué Moulure CouronnéeEntretien Inspection ET Remplacement DE LA BrosseGuide de dépannage Manual DE Instrucciones Instrucciones Importantes Sobre Seguridad Definiciones DE LAS Normas DE SeguridadNormas Generales DE Seguridad Page Conserve Estas Instrucciones Conexiones Eléctricas Otras Reglas DE Seguridad Para EL LáserEspecificaciones DEL Motor Instrucciones DE Conexión a TierraIntroducción Cables ProlongadoresDescripción DE LAS Funciones Montaje Desembalaje Y LimpiezaContenido DE LA Caja Controles DE Operación Y Ajustes Bloqueo DEL Cabezal DE Corte EN LA Posición Hacia Abajo Indicador Y EscalaInclinación DEL Cabezal DE Corte Para EL Corte Biselado Ajuste DE LA Guía DeslizanteAjuste DEL Protector Inferior DE LA Hoja Ajuste DEL Recorrido Descendente DE LA Hoja DE LA SierraDesconecte LA Máquina DE LA Fuente DE Alimentación No Retire Ninguno DE LOS Protectores DE LA HojaFuncionamiento DEL Láser Utilización Y Regulación DEL LáserCómo Controlar LA Alineación DEL Láser Verificación DE LA Alineación VerticalMantenimiento DEL Láser Operaciones Típicas Y Consejos ÚtilesGuía Auxiliar Para Madera Operaciones Generales DE CorteMolduras DE Corona MantenimientoCorte DE Material Curvado Importante Inspección Y Reemplazo DE LOS CepillosInformación de mantenimiento
Top Page Image Contents