Black & Decker FS110L instruction manual Laser USE and Adjustment, Adjusting the Lower Blade Guard

Page 14

ADJUSTING THE LOWER BLADE GUARD

DISCONNECT THE MACHINE FROM

POWER SOURCE.

This machine incorporates a blade guard (A) Fig. 27B to cover the rear section of the blade. After an extended period of use, the movable lower blade guard may not operate smoothly when the cuttinghead is lowered. This can be corrected by adjusting nut (B) until the lower blade guard moves freely.

Overtightening the nut could impair guard movement.

NOTE: This unit has been designed with an articulating rear guard. Before contacting the workpiece, the rear guard will rotate upward to expose more of the blade as the cuttinghead is lowered.

DO NOT REMOVE ANY OF THE BLADE GUARDS.

Fig. 27B

A

B

Make sure that all guards are in place and functioning properly before operating the saw.

Make sure that the fences are clear of the guard and blade before operating the saw.

LASER USE AND ADJUSTMENT

HOW THE LASER WORKS

The battery-operated laser unit (AA batteries not included) is mounted in a housing that is fitted into the upper blade guard of the miter saw (Fig. A). (To insert the batteries, remove the screw (C) Fig. B, and slide the battery cover (D) from the handle.) The laser projects a beam of light downward. This beam of light produces a red line-of-cut indicator, where the saw blade will cut the workpiece. The laser unit is aligned at the factory and secured in place. A test cut has been made with each saw to verify the laser setup. If your saw becomes misaligned or you desire additional precision, use the following guidelines to fine tune your laser miter saw.

HOW TO CHECK LASER ALIGNMENT

Make sure the saw is set to 0 degrees miter and bevel and clamp a 2"x 4" board on the saw. Create a partial/test cut in the workpiece (Fig. C). Turn the laser “ON/OFF” switch (A) Fig. B) to the “ON” position. Leave the workpiece clamped in place for the remainder of the adjustment.

Place and lock a padlock with a 3/16" shackle (B) Fig. B through the hole in the trigger switch to prevent accidental motor startup.The padlock MUST remain in place during the adjustment procedure.

The laser line is properly positioned when the beam of light falls on the cut created by the blade (Fig. D).

14

Image 14

Contents FS110L 10 Compound Laser Miter SAW Before Returning this Product for ANY Reason Please CallImportant Safety Instructions Safety Guidelines DefinitionsGeneral Safety Rules Stay ALERT, Watch What YOU are Doing Additional Safety Rules for Miter Saws Failure to Follow These Rules MAY Result in Serious InjuryMotor Specifications Additional Safety Rules for the LaserPower Connections Grounding InstructionsFunctional Description Unpacking and CleaningExtension Cords ForewordCarton Contents AssemblyFastening Machine to Supporting Surface Operating Controls and AdjustmentsAttaching Dust BAG Table Hazard AreaRotating the Table for Miter Cutting Locking the Switch in the OFF PositionStarting and Stopping the Miter SAW Locking Cuttinghead in the Down Position Disconnect the Machine from Power SourcePointer and Scale Tilting Cuttinghead for Bevel CuttingSide Supports Adjusting Sliding FenceRear STABILIZER/CARRYING Handle Adjusting 90 and 45 Bevel Stops Adjusting Blade Parallel to Table SlotAdjusting Downward Travel of SAW Blade Disconnect Machine from Power SourceAdjusting Tension of Cuttinghead Return Spring Adjusting Sliding FIT Between Cuttinghead ARM and TrunnionHOW to Check Laser Alignment Laser USE and AdjustmentAdjusting the Lower Blade Guard HOW the Laser WorksTo Check for Vertical Alignment To SET Kerf AdjustmentLaser Maintenance General Cutting Operations Typical Operations and Helpful HintsAuxiliary Wood Fence Right Wrong Cutting AluminumCutting Bowed Material Crown Molding Cutting Crown MoldingMaintenance Changing the BladeBrush Inspection Replacement Trouble Shooting Guide Mode D’EMPLOI Directives DE Sécurité Importantes Lignes Directrices EN Matière DE Sécurité DéfinitionsRègles Générales DE Sécurité Page Conserver CES Directives Caractéristiques Techniques DU Moteur Règles DE Sécurité Supplémentaires Pour LE LaserConnexions Électriques Directives DE Mise À LA TerreDésemballage ET Nettoyage Rallonges ÉlectriquesDescription Fonctionnelle Utilisation DES Contrôle ET Réglages Contenu DU CartonAssemblage Rotation DE LA Table Pour Effectuer UNE Coupe À Onglet Démarrage ET Arrêt DE LA Scie À OngletsVerrouillage DE Linterrupteur EN Position Darrêt Pointeur ET ÉchelleSupports Latéraux Réglage DU Guide CoulissantStabilisateur ARRIÈRE/POIGNÉE DE Transport Ajustement DE LA Lame Parralèle À LA Fente DE LA TableFonctionnement DU Laser Utilisation ET Réglage DU LaserRéglage DU PROTÈGE-LAME Inférieur Vérification DE L’ALIGNEMENT DU LaserRéglage DU Trait DE Scie Opérations Courantes ET Conseils UtilesVérification DE L’ALIGNEMENT Vertical Entretien DU LaserCoupe DE Matériau Arqué Opérations DE Coupe GénéralesCoupe Daluminium Moulure CouronnéeInspection ET Remplacement DE LA Brosse EntretienGuide de dépannage Manual DE Instrucciones Instrucciones Importantes Sobre Seguridad Definiciones DE LAS Normas DE SeguridadNormas Generales DE Seguridad Page Conserve Estas Instrucciones Especificaciones DEL Motor Otras Reglas DE Seguridad Para EL LáserConexiones Eléctricas Instrucciones DE Conexión a TierraIntroducción Cables ProlongadoresDescripción DE LAS Funciones Montaje Desembalaje Y LimpiezaContenido DE LA Caja Controles DE Operación Y Ajustes Inclinación DEL Cabezal DE Corte Para EL Corte Biselado Indicador Y EscalaBloqueo DEL Cabezal DE Corte EN LA Posición Hacia Abajo Ajuste DE LA Guía DeslizanteDesconecte LA Máquina DE LA Fuente DE Alimentación Ajuste DEL Recorrido Descendente DE LA Hoja DE LA SierraAjuste DEL Protector Inferior DE LA Hoja No Retire Ninguno DE LOS Protectores DE LA HojaCómo Controlar LA Alineación DEL Láser Utilización Y Regulación DEL LáserFuncionamiento DEL Láser Verificación DE LA Alineación VerticalGuía Auxiliar Para Madera Operaciones Típicas Y Consejos ÚtilesMantenimiento DEL Láser Operaciones Generales DE CorteMolduras DE Corona MantenimientoCorte DE Material Curvado Inspección Y Reemplazo DE LOS Cepillos ImportanteInformación de mantenimiento