Black & Decker FS110L instruction manual Trouble Shooting Guide

Page 21

Trouble Shooting Guide

BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS

TROUBLE! SAW WILL NOT START

 

WHAT’S WRONG?

WHAT TO DO…

1.Saw not plugged in.

1.Plug in saw.

2.Fuse blown or circuit breaker tripped.

2.Replace fuse or reset

 

circuit breaker.

3.Cord damaged.

3.Have cord replaced by

 

authorized service center.

4.Brushes worn out.

4.Have brushes replaced

 

by authorized service center.

TROUBLE! SAW MAKES UNSATISFACTORY CUTS

WHAT’S WRONG?

WHAT TO DO…

1.Dull blade.

1.Replace blade.

2.Blade mounted backwards.

2.Turn blade around.

3.Gum or pitch on blade.

3.Remove blade and

 

clean with turpentine.

4.Incorrect blade for work being done.

4.Change the blade.

TROUBLE! BLADE DOES NOT COME UP TO SPEED

WHAT’S WRONG?

WHAT TO DO…

1.Extension cord too light or too long.

1.Replace with adequate

 

size cord.

2.Low house current.

2.Contact your electric

 

company.

TROUBLE! MACHINE VIBRATES EXCESSIVELY

WHAT’S WRONG?

WHAT TO DO…

1.Saw not mounted securely.

1.Tighten all mounting

 

hardware.

2.Stand or bench on uneven floor.

2.Reposition on flat level

 

surface.

3.Damaged saw blade.

3.Replace blade.

TROUBLE! DOES NOT MAKE ACCURATE MITER CUTS

WHAT’S WRONG?

WHAT TO DO…

1.Miter scale not adjusted correctly.

1.Check and adjust.

2.Blade is not square to fence.

2.Check and adjust.

3.Blade is not perpendicular to table.

3.Check and adjust fence.

4.Workpiece moving.

4.Clamp workpiece to

 

fence or glue 120 grit

 

sandpaper to fence with

 

rubber cement.

TROUBLE! MATERIAL PINCHES BLADE

 

WHAT’S WRONG?

WHAT TO DO…

1.Cutting bowed material.

1.Position bowed material

 

as shown in Figure 33.

Service Information

Black & Decker offers a full network of company-owned and authorized service locations throughout NorthAmerica.All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service.

Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call: 1-800-54-HOWTO (544-6986).

Accessories

CAUTION:The use of any non-recommended accessory such as dado sets, molding cutters or abrasive wheels may be hazardous.

Full Two-Year Home Use Warranty

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship.The defective product will be replaced or repaired at no charge in either of two ways:

The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized service centers are listed under "Tools-Electric" in the yellow pages of the phone directory.

This warranty does not apply to accessories.This warranty gives you specific legal rights and you may have other rights which vary from state to state. Should you have any questions, contact the manager of your nearest Black & Decker Service Center.

This product is not intended for commercial use.

FREE WARNING LABELREPLACEMENT: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free replacement.

Special WARRANTY Note to Contractors:

FIRESTORMTM branded products are offered as high end consumer home usetools and carry a HOME USE WARRANTY.These tools are designed, manufactured and tested to meet or exceed the needs of the do-it-yourselfer in the execution of projects and repairs in and around the home. With proper use they will provide the home owner with step up power and performance well beyond their two year warranty. However, if you use tools for a living and use FIRESTORMTM branded products or any of Black & Decker’s other Consumer Home Use tools ON THE JOBSITE you should know that they CANNOT BE COVERED UNDER OUR WARRANTY.

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

21

Image 21
Contents Before Returning this Product for ANY Reason Please Call FS110L 10 Compound Laser Miter SAWSafety Guidelines Definitions General Safety RulesImportant Safety Instructions Stay ALERT, Watch What YOU are Doing Failure to Follow These Rules MAY Result in Serious Injury Additional Safety Rules for Miter SawsPower Connections Additional Safety Rules for the LaserMotor Specifications Grounding InstructionsExtension Cords Unpacking and CleaningFunctional Description ForewordAssembly Carton ContentsAttaching Dust BAG Operating Controls and AdjustmentsFastening Machine to Supporting Surface Table Hazard AreaLocking the Switch in the OFF Position Starting and Stopping the Miter SAWRotating the Table for Miter Cutting Pointer and Scale Disconnect the Machine from Power SourceLocking Cuttinghead in the Down Position Tilting Cuttinghead for Bevel CuttingAdjusting Sliding Fence Rear STABILIZER/CARRYING HandleSide Supports Adjusting Downward Travel of SAW Blade Adjusting Blade Parallel to Table SlotAdjusting 90 and 45 Bevel Stops Disconnect Machine from Power SourceAdjusting Sliding FIT Between Cuttinghead ARM and Trunnion Adjusting Tension of Cuttinghead Return SpringAdjusting the Lower Blade Guard Laser USE and AdjustmentHOW to Check Laser Alignment HOW the Laser WorksTo SET Kerf Adjustment Laser MaintenanceTo Check for Vertical Alignment Typical Operations and Helpful Hints Auxiliary Wood FenceGeneral Cutting Operations Cutting Aluminum Cutting Bowed MaterialRight Wrong Cutting Crown Molding Crown MoldingChanging the Blade MaintenanceBrush Inspection Replacement Trouble Shooting Guide Mode D’EMPLOI Lignes Directrices EN Matière DE Sécurité Définitions Règles Générales DE SécuritéDirectives DE Sécurité Importantes Page Conserver CES Directives Connexions Électriques Règles DE Sécurité Supplémentaires Pour LE LaserCaractéristiques Techniques DU Moteur Directives DE Mise À LA TerreRallonges Électriques Description FonctionnelleDésemballage ET Nettoyage Contenu DU Carton AssemblageUtilisation DES Contrôle ET Réglages Verrouillage DE Linterrupteur EN Position Darrêt Démarrage ET Arrêt DE LA Scie À OngletsRotation DE LA Table Pour Effectuer UNE Coupe À Onglet Pointeur ET ÉchelleStabilisateur ARRIÈRE/POIGNÉE DE Transport Réglage DU Guide CoulissantSupports Latéraux Ajustement DE LA Lame Parralèle À LA Fente DE LA TableRéglage DU PROTÈGE-LAME Inférieur Utilisation ET Réglage DU LaserFonctionnement DU Laser Vérification DE L’ALIGNEMENT DU LaserVérification DE L’ALIGNEMENT Vertical Opérations Courantes ET Conseils UtilesRéglage DU Trait DE Scie Entretien DU LaserCoupe Daluminium Opérations DE Coupe GénéralesCoupe DE Matériau Arqué Moulure CouronnéeEntretien Inspection ET Remplacement DE LA BrosseGuide de dépannage Manual DE Instrucciones Definiciones DE LAS Normas DE Seguridad Normas Generales DE SeguridadInstrucciones Importantes Sobre Seguridad Page Conserve Estas Instrucciones Conexiones Eléctricas Otras Reglas DE Seguridad Para EL LáserEspecificaciones DEL Motor Instrucciones DE Conexión a TierraCables Prolongadores Descripción DE LAS FuncionesIntroducción Desembalaje Y Limpieza Contenido DE LA CajaMontaje Controles DE Operación Y Ajustes Bloqueo DEL Cabezal DE Corte EN LA Posición Hacia Abajo Indicador Y EscalaInclinación DEL Cabezal DE Corte Para EL Corte Biselado Ajuste DE LA Guía DeslizanteAjuste DEL Protector Inferior DE LA Hoja Ajuste DEL Recorrido Descendente DE LA Hoja DE LA SierraDesconecte LA Máquina DE LA Fuente DE Alimentación No Retire Ninguno DE LOS Protectores DE LA HojaFuncionamiento DEL Láser Utilización Y Regulación DEL LáserCómo Controlar LA Alineación DEL Láser Verificación DE LA Alineación VerticalMantenimiento DEL Láser Operaciones Típicas Y Consejos ÚtilesGuía Auxiliar Para Madera Operaciones Generales DE CorteMantenimiento Corte DE Material CurvadoMolduras DE Corona Importante Inspección Y Reemplazo DE LOS CepillosInformación de mantenimiento