Samsung AP50M0ANXSG manual Space requirements, Wear protective goggles and mask before spraying

Page 33

WARNING

CAUTION

•After installing the outdoor unit, apply rust inhibitor on the internal pipes and heat exchanger.

-- If you don’t apply rust inhibitor, airborne corrosive gas (such as sulfur compounds, hydrogen sulfide and ammonia) and salty dust may cause pipe corrosion which will lead to refrigerant leakage.

-- Inspect the outdoor unit at least once a year and re-apply the rust inhibitor where it is damaged (worn out).

•When applying the rust inhibitor, please be aware of the following: -- Turn off the power before spraying the rust inhibitor.

-- Wear protective goggles and mask before spraying.

-- Clean the dusty surface with clean fabric or paper before spraying. -- Make sure that wind is blowing from worker’s back when spraying. -- Do not spray on the PCB panel and electric parts.

•Install the indoor unit away from any interfering sources such as radio, computer, stereo equipment and also select the place where the electrical wiring work can be possible.

-- Especially keep the unit at least 3m away from the electrical equipment in an area electromagnetic waves generated and install the protection tube to protect the main power cable and communication cable.

-- Make sure that there is no equipment electromagnetic waves generate. If not, malfunction of the control system may occur due to the effect of the electromagnetic wave. (For example: The remote control sensor of the indoor unit may not be received well of electronic lighting style fluorescent lamps, such as fluorescent lamps are in the same space when using a remote control.)

•Make sure to install the outdoor unit in a safe place where snowfall will not be obstructed. The frame should be installed in a place where the air inlet and heat exchanger of the unit are not buried in the snow.

•A ventilation system may be required in the case the outdoor unit is installed in a closed space or room, even though R-410A is not poisonous or flammable.

•Install the railing around the outdoor unit to prevent falling when the unit is installed at high place of roof on the building.

•Avoid installing the units in places such as an exhaust pipe and ventilating opening exposed to corrosive gas, oxides of sulfur, ammonia gas or sulfur gas herbicides. (These places need additional anticorrosive treatments. Please contact manufacture to avoid corroding copper pipes or soldered parts)

•Depending on the condition of power supply, unstable power or voltage may cause malfunction of the parts or control system. (At the ship or places using power supply from electric generator, etc)

ENGLISH

Space requirements

ffThe space suggested below is based on operating condition of outdoor temperature of 35°C. If operating condition of outdoor temperature is higher than 35°C, try to have more space.

ffMake sure to clear a passage for a person and air flow.

ffObserve the clearances and dimensions as seen below when installing the outdoor unit.

fIfyou install several outdoor units at the same place, observe the space for ventilation and free airflow.

fIfthe space for ventilation is insufficient, the air conditioner may not generate performance designed. Keep in mind that SAMSUNG logo is located on the front side of outdoor unit.

33

Mirage_AP50M0@_IBIM_EN_05323A-02.indd 33

2016-05-19 오후 1:27:20

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Thank you for purchasing this Samsung product Air ConditionerFeatures of your new air conditioner Strong Turbo/Long FunctionLook for Everywhere Contents Safety precautions Important safety symbols and precautionsDo not yank the power cable with hands Ensure no water gets into the air conditioner FfPotential risk of injury or electric shock Use a rated circuit breaker onlyFfPotential risk of personal injury Do not open the front panel during operationDo not allow children to climb on the air conditioner FfInsufficient ventilation may result in poor performanceFfPotential risk of personal injury or property loss FfWearing thick gloves can protect your hands Checking the indoor unit and display Viewing your air conditionerMain parts To open the panelHeater and Purity function is not supported by this model Control panelRemote controller buttons Checking the remote controllerRemote controller display Using the remote controllerAre in the same space Storing the remote controller Battery changing timeInserting the batteries Indoor unitBasic operation Selecting the operation mode Turning on the powerAdjusting the desired temperature Selecting the fan speedSelecting air flow direction When the air conditioner is off Setting the On/Off timerYou cannot set the fan speed when setting the On timer Controller displayButton When the air conditioner is onWhen the air conditioner is operating in Cool or Heat mode Using the Turbo functionLocking the control panel Using the Long functionUsing the air conditioner with the control panel Cleaning and maintaining the air conditioner Cleaning the exteriorCleaning the filter Air filter Installation part Maintaining your air conditionerPeriodical checks Internal protections via the unit control system Have deposited at low temperaturesAppendix TroubleshootingHumidity Operation rangesOr accessing its internal components Installing the unitGeneral information PersonnelDo not install the air conditioner in following places Power supply line, fuse or circuit breakerMake sure that you earth the cables Complete, electric shock or fire may occurAccessory parts list Indoor unit Selection of installation placeTop view Side viewOutdoor unit Preparing the installation Selecting appropriate location for installationVentilate Wear protective goggles and mask before spraying Space requirementsElectrical work Wiring standardCord. Code designation IEC60245 IEC 66 / CENELECH07RN-F Ssc *2Indoor and outdoor connection wiring Using 4poles ELCBEarth Leakage Circuit BreakerAP50M0 Series AP50M1 Series Using 3poles Elcb and 2poles ElcbConnecting the power terminal Electrical wiringOutdoor unit When using the anchor bolt Installation methodWhen using the rubber leg Installation proceduresTrap Refrigerant pipe work Insulating the pipes Check the following list and install an oil trapOil trap FfRadius of curvature R on the oil trap are as followsConnection of refrigerant piping Flare processing Cut the pipe using the pipe cutterRemove burr on the edge of pipe It may cause explosion and injuryPipe bending Tightening of connection partsDrilling a hole in the wall Drain hose Wall installation Corner InstallationFixing the indoor unit ExampleBe sure that all valve cocks are closed Air purgeHow to add refrigerant Refrigerant chargingCheck the stability of the pressure for 10 minutes Check and test operation CheckIs grounding properly made? Pump down procedure When removing the product When the outdoor temperature is below zero, do notTest operation Packing and unpacking guide Outdoor unit Mm of the wire shields of the tube How to connect your extended power cablesPrepare the following tools TubeApply heat to the contraction tube to contract it FfMethodMirageAP50M0@IBIMEN05323A-02.indd 2016-05-19 오후 English Questions or COMMENTS?
Top Page Image Contents