Samsung AP50M1ANXSG, AP50M0ANXSG manual Packing and unpacking guide, Indoor unit

Page 48

Packing and unpacking guide

Indoor unit

Cushion-top ①

Cushion-mid ②

Packing case ③

Indoor unit ④

Cushion-bottom ⑤

ffPacking the unit as below procedure

1.Put the indoor unit ④ onto the cushion-bottom ⑤.

2.Assemble cushion-mid ② of indoor unit ④.

3.Put the cushion-top ① onto the indoor unit ④.

4.Put the packing case ③ from the top of set.

5.Seal the packing case ③.

ffUnpacking the unit as below procedure

1.Take out the packing case ③ from the set.

2.Take out the cushion-top ①.

3.Take out the cushion-mid ②.

4.Move the set from the cushion-bottom ⑤.

Mirage_AP50M0@_IBIM_EN_05323A-02.indd 48

2016-05-19 오후 1:27:29

Image 48

Contents Air Conditioner Thank you for purchasing this Samsung productFeatures of your new air conditioner Strong Turbo/Long FunctionLook for Everywhere Contents Safety precautions Important safety symbols and precautionsDo not yank the power cable with hands Ensure no water gets into the air conditioner Use a rated circuit breaker only FfPotential risk of injury or electric shockFfPotential risk of personal injury Do not open the front panel during operationDo not allow children to climb on the air conditioner FfInsufficient ventilation may result in poor performanceFfPotential risk of personal injury or property loss FfWearing thick gloves can protect your hands Viewing your air conditioner Checking the indoor unit and displayMain parts To open the panelControl panel Heater and Purity function is not supported by this modelChecking the remote controller Remote controller buttonsRemote controller display Using the remote controllerAre in the same space Battery changing time Storing the remote controllerInserting the batteries Indoor unitBasic operation Turning on the power Selecting the operation modeAdjusting the desired temperature Selecting the fan speedSelecting air flow direction Setting the On/Off timer When the air conditioner is offYou cannot set the fan speed when setting the On timer Controller displayWhen the air conditioner is on ButtonUsing the Turbo function When the air conditioner is operating in Cool or Heat modeUsing the Long function Locking the control panelUsing the air conditioner with the control panel Cleaning and maintaining the air conditioner Cleaning the exteriorCleaning the filter Air filter Installation part Maintaining your air conditionerPeriodical checks Have deposited at low temperatures Internal protections via the unit control systemTroubleshooting AppendixOperation ranges HumidityInstalling the unit Or accessing its internal componentsGeneral information PersonnelPower supply line, fuse or circuit breaker Do not install the air conditioner in following placesMake sure that you earth the cables Complete, electric shock or fire may occurAccessory parts list Selection of installation place Indoor unitTop view Side viewOutdoor unit Preparing the installation Selecting appropriate location for installationVentilate Space requirements Wear protective goggles and mask before sprayingWiring standard Electrical workCord. Code designation IEC60245 IEC 66 / CENELECH07RN-F Ssc *2Indoor and outdoor connection wiring Using 4poles ELCBEarth Leakage Circuit BreakerAP50M0 Series Using 3poles Elcb and 2poles Elcb AP50M1 SeriesElectrical wiring Connecting the power terminalInstallation method Outdoor unit When using the anchor boltWhen using the rubber leg Installation proceduresTrap Check the following list and install an oil trap Refrigerant pipe work Insulating the pipesOil trap FfRadius of curvature R on the oil trap are as followsCut the pipe using the pipe cutter Connection of refrigerant piping Flare processingRemove burr on the edge of pipe It may cause explosion and injuryPipe bending Tightening of connection partsDrilling a hole in the wall Wall installation Corner Installation Drain hoseFixing the indoor unit ExampleAir purge Be sure that all valve cocks are closedHow to add refrigerant Refrigerant chargingCheck the stability of the pressure for 10 minutes Check and test operation CheckIs grounding properly made? Pump down procedure When removing the product When the outdoor temperature is below zero, do notTest operation Packing and unpacking guide Outdoor unit How to connect your extended power cables Mm of the wire shields of the tubePrepare the following tools TubeFfMethod Apply heat to the contraction tube to contract itMirageAP50M0@IBIMEN05323A-02.indd 2016-05-19 오후 English Questions or COMMENTS?