Samsung AP50M0ANXSG, AP50M1ANXSG manual Indoor and outdoor connection wiring, AP50M0 Series

Page 35

Indoor and outdoor connection wiring

ffWhen connecting the wiring harness between the indoor and outdoor unit, align the outdoor side and the indoor side with the terminal board No.

❋❋When the wiring harnesses of the indoor and outdoor unit are not properly connected, it may cause trouble. Be careful not to allow the indoor and outdoor wirings and power lines to get in contact with the service valve of the refrigerant system or to the pipe without an insulation.

AP50M0✴ Series

Using 4poles ELCB(Earth Leakage Circuit Breaker)

1.Remove the cover of electric box on side panel of the outdoor unit.

2.Connect the electric input wires [L1(R), L2(S), L3(T), N] to each terminal [L1(R), L2(S), L3(T), N] of the electric box on the outdoor unit respectively. (Input wires are purchased by the user separately.)

3.Connect the electric wires to each terminal on the indoor and outdoor unit respectively.

ENGLISH

Control box

Indoor unit

Earth

Earth

Earth

Indoor and outdoor connection wire

Outdoor Unit

Knife switch or

automatic circuit

breaker

ON

R S T N

Earth

Power cable

(Purchase separately)

35

Mirage_AP50M0@_IBIM_EN_05323A-02.indd 35

2016-05-19 오후 1:27:21

Image 35

Contents Thank you for purchasing this Samsung product Air ConditionerLook for Everywhere Features of your new air conditionerStrong Turbo/Long Function Contents Do not yank the power cable with hands Safety precautionsImportant safety symbols and precautions Ensure no water gets into the air conditioner Do not open the front panel during operation Use a rated circuit breaker onlyFfPotential risk of injury or electric shock FfPotential risk of personal injuryFfPotential risk of personal injury or property loss Do not allow children to climb on the air conditionerFfInsufficient ventilation may result in poor performance FfWearing thick gloves can protect your hands To open the panel Viewing your air conditionerChecking the indoor unit and display Main partsHeater and Purity function is not supported by this model Control panelRemote controller buttons Checking the remote controllerAre in the same space Remote controller displayUsing the remote controller Indoor unit Battery changing timeStoring the remote controller Inserting the batteriesBasic operation Selecting the fan speed Turning on the powerSelecting the operation mode Adjusting the desired temperatureSelecting air flow direction Controller display Setting the On/Off timerWhen the air conditioner is off You cannot set the fan speed when setting the On timerButton When the air conditioner is onWhen the air conditioner is operating in Cool or Heat mode Using the Turbo functionLocking the control panel Using the Long functionUsing the air conditioner with the control panel Cleaning the filter Air filter Cleaning and maintaining the air conditionerCleaning the exterior Periodical checks Installation partMaintaining your air conditioner Internal protections via the unit control system Have deposited at low temperaturesAppendix TroubleshootingHumidity Operation rangesPersonnel Installing the unitOr accessing its internal components General informationComplete, electric shock or fire may occur Power supply line, fuse or circuit breakerDo not install the air conditioner in following places Make sure that you earth the cablesAccessory parts list Side view Selection of installation placeIndoor unit Top viewOutdoor unit Ventilate Preparing the installationSelecting appropriate location for installation Wear protective goggles and mask before spraying Space requirementsSsc *2 Wiring standardElectrical work Cord. Code designation IEC60245 IEC 66 / CENELECH07RN-FAP50M0 Series Indoor and outdoor connection wiringUsing 4poles ELCBEarth Leakage Circuit Breaker AP50M1 Series Using 3poles Elcb and 2poles ElcbConnecting the power terminal Electrical wiringInstallation procedures Installation methodOutdoor unit When using the anchor bolt When using the rubber legTrap FfRadius of curvature R on the oil trap are as follows Check the following list and install an oil trapRefrigerant pipe work Insulating the pipes Oil trapIt may cause explosion and injury Cut the pipe using the pipe cutterConnection of refrigerant piping Flare processing Remove burr on the edge of pipeDrilling a hole in the wall Pipe bendingTightening of connection parts Example Wall installation Corner InstallationDrain hose Fixing the indoor unitBe sure that all valve cocks are closed Air purgeCheck the stability of the pressure for 10 minutes How to add refrigerantRefrigerant charging Is grounding properly made? Check and test operationCheck Test operation Pump down procedure When removing the productWhen the outdoor temperature is below zero, do not Packing and unpacking guide Outdoor unit Tube How to connect your extended power cablesMm of the wire shields of the tube Prepare the following toolsApply heat to the contraction tube to contract it FfMethodMirageAP50M0@IBIMEN05323A-02.indd 2016-05-19 오후 English Questions or COMMENTS?