Heat & Glo LifeStyle SL-750TRS-IPI-D owner manual

Page 10

(NG, LP) Service Parts List

SL-750TRS-IPI-D

IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When order- ing, supply serial and model numbers to ensure correct service parts.

ITEM	DESCRIPTION	SERIAL #	PART NUMBER

	Burner Orifice NG (#36C)		582-836

	Burner Orifice LP (#52C)		582-852

1	Junction Box		4021-013

2	Burner NG		2066-005

2	Burner LP		2065-006

3	Glass Door Assembly		GLA-750TRS

4	Log Grate		2066-036

5	Base Refractory NG, LP		2066-100

6	Hood		SRV530-175

7	Log Set Assembly		LOGS-750TRS-D

8	Log 1		SRV2065-701

9	Log 2		SRV2066-702

10	Log 3		SRV2066-703

11	Log 4		SRV2066-704

12	Log 5		SRV2066-705

	Refractory Kit		BRICK-750TRS-D

13	Refractory, Back		SRV2045-711

14	Refractory, Left Side		SRV2045-710

15	Refractory, Right Side		SRV2045-712

	Mineral Wool		050-721

	Glass Latch Assembly		386-122A

	Exhaust Restrictor		530-299

	Touch up Paint		TUP-GBK-12

	ACCESSORIES

	Fan Kit		GFK-160A

	Extended Vertical Baffle Kit		BAF-VERT

	Wall Switch Kit, Off-white		WSK-21

	Wall Switch Kit, White		WSK-21-W

	Conversion Kit NG		NGK-750TRS-IPID

	Conversion Kit LP		LPK-750TRS-IPID

	Vermiculite Embers		MYSTIC-EMBERS

Í

Í

Í

Also see additional pages for valve assembly service part numbers.

10	Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

Image 10

Contents Installation and Operation SL-750TRS-IPI-D SL-550TRS-IPI-D SL-350TRS-CSafety and Warning Information Table of Contents Log Set Assembly SL-350TRS-CNG, LP Service Parts List SL-350TRS-CValve Assembly Standing Pilot IgnitionSL-550TRS-IPI-D SL-550TRS-IPI-D Log Set Assembly Part number list on followingSL-750TRS-IPI-D Service Parts SL-750TRS-IPI-D, SL-550TRS-IPI-D Intermittent Pilot Ignition Valve AssemblyAppliance Certification High Altitude InstallationsInstallation Codes CertificationVent Directly BELOW. Keep Clear of ALL OB- Structions Requirements for the Commonwealth of MassachusettsManufacturer Requirements Introducing the Heat & Glo Gas Appliances Pre-install PreparationANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the SL-750TRS-IPI-D GAS Line Electrical Access Access Diagram of the SL-350TRS-CLocating the Appliance Constructing the Appliance ChaseClearance Requirements Framing Dimensions Framing the Appliance34.93mm AT Each Joint 47 3/4 Identifying Vent Components Installing the Vent SystemSystem Configuration SL D-SERIES Components in ANY VentStraight UP Vertical Venting Flex VentWith TWO 900 Elbows Use DVP-Series Components only Venting with One 90 Elbow Use SL D-Series components onlyVenting with Two 90 Elbows Venting with TWO 2 90 o Elbows MAX. = 16 FT 4.8m + V 1 + H MAX. = 40 FT 12.2m Venting with Three 90 elbows Venting with Three 3 90 o Elbows + H 1 MAX. = 16 FT 4.8m + V 1 + H + H MAX. = 40 FT 12.2m Venting with Four 90 elbows Go to Install Firestops DVP Series Venting OnlySL-D and SL-Flex Series Venting Only Attach the First Vent Component to the Starting CollarsDVP, SL-D and SL-Flex Series Venting Hole and Vent PipeFor DVP Venting Only Vent TerminationSL-Series Venting Only For All VentingAlcove Applications Vent Termination Minimum ClearancesMinimum Height from Roof to Lowest Discharge Opening Standing Pilot Ignition System Positioning, Leveling, and Securing the ApplianceGas Control Systems Millivolt SystemGas Pressure Requirements Gas Supply LinePressure Natural Gas Propane Optional Accessories Wiring the ApplianceFor Standing Pilot Ignition Wiring Appliance Requirements Wall SwitchOperation using Battery Power Intermittent Pilot Ignition IPI Wiring DiagramFinishing NERGlass Specifications Installing the TrimShutter Settings Positioning the LogsBefore Lighting the Appliance After the InstallationDouble-check for faulty components Lighting the ApplianceAppliance Maintenance Important Turn OFF the GAS Before Servicing Your Appliance