Heat & Glo LifeStyle SL-750TRS-IPI-D owner manual Venting with Two 90 Elbows

Page 25

V	H		H + H1
1' MIN. (305 mm)	2' MAX. (610 mm)		4' MAX. (1.22m)
2' MIN. (610 mm)	4' MAX. (1.22 m)		8' MAX. (2.4m)
3' MIN. (914 mm)	6' MAX. (1.86 m)		12' MAX. (3.6m)
4' MIN. (1.22 m)	8' MAX. (2.48 m)		16' MAX. (4.8m)
V+H+H1 = 40' MAX. (12.4 m)		H = 8' MAX. (2.48 m)	H+H1 = 16' MAX. (4.8m)
H1
		V
Use DVP-Series
components only.			H
			H
V (FT)		H + H1 (FT)
1' MIN. (305 mm)		2' MAX. (610 mm)
2' MIN. (610 mm)		4' MAX. (1.22 m)
3' MIN. (914 mm)		6' MAX. (1.86 m)
4' MIN. (1.22 m)		8' MAX. (2.48 m)
V		H + H1= 8' MAX. (2.48 m)
V + H + H1= 40' (12.2m) MAX.
H1
			H
Figure 14. Venting with Two 90° Elbows
Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06				25

Image 25

Contents SL-750TRS-IPI-D SL-550TRS-IPI-D SL-350TRS-C Installation and OperationSafety and Warning Information Table of Contents SL-350TRS-C Log Set AssemblySL-350TRS-C NG, LP Service Parts ListStanding Pilot Ignition Valve AssemblySL-550TRS-IPI-D SL-550TRS-IPI-D Part number list on following Log Set AssemblySL-750TRS-IPI-D Intermittent Pilot Ignition Valve Assembly Service Parts SL-750TRS-IPI-D, SL-550TRS-IPI-DInstallation Codes High Altitude InstallationsAppliance Certification CertificationVent Directly BELOW. Keep Clear of ALL OB- Structions Requirements for the Commonwealth of MassachusettsManufacturer Requirements Introducing the Heat & Glo Gas Appliances Pre-install PreparationANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the SL-750TRS-IPI-D GAS Line Electrical Access Diagram of the SL-350TRS-C AccessLocating the Appliance Constructing the Appliance ChaseClearance Requirements Framing the Appliance Framing Dimensions34.93mm AT Each Joint 47 3/4 System Configuration Installing the Vent SystemIdentifying Vent Components SL D-SERIES Components in ANY VentStraight UP Vertical Venting Flex VentWith TWO 900 Elbows Venting with One 90 Elbow Use SL D-Series components only Use DVP-Series Components onlyVenting with Two 90 Elbows Venting with TWO 2 90 o Elbows MAX. = 16 FT 4.8m + V 1 + H MAX. = 40 FT 12.2m Venting with Three 90 elbows Venting with Three 3 90 o Elbows + H 1 MAX. = 16 FT 4.8m + V 1 + H + H MAX. = 40 FT 12.2m Venting with Four 90 elbows DVP Series Venting Only Go to Install FirestopsAttach the First Vent Component to the Starting Collars SL-D and SL-Flex Series Venting OnlyHole and Vent Pipe DVP, SL-D and SL-Flex Series VentingSL-Series Venting Only Vent TerminationFor DVP Venting Only For All VentingVent Termination Minimum Clearances Alcove ApplicationsMinimum Height from Roof to Lowest Discharge Opening Gas Control Systems Positioning, Leveling, and Securing the ApplianceStanding Pilot Ignition System Millivolt SystemGas Pressure Requirements Gas Supply LinePressure Natural Gas Propane For Standing Pilot Ignition Wiring Appliance Requirements Wiring the ApplianceOptional Accessories Wall SwitchIntermittent Pilot Ignition IPI Wiring Diagram Operation using Battery PowerNER FinishingShutter Settings Installing the TrimGlass Specifications Positioning the LogsDouble-check for faulty components After the InstallationBefore Lighting the Appliance Lighting the ApplianceImportant Turn OFF the GAS Before Servicing Your Appliance Appliance Maintenance