Heat & Glo LifeStyle owner manual Service Parts SL-750TRS-IPI-D, SL-550TRS-IPI-D

Page 11

Service Parts SL-750TRS-IPI-D, SL-550TRS-IPI-D

(NG, LP) Exploded Parts Diagram	Beginning Manufacturing Date: 4-04
	Ending Manufacturing Date: ______

Intermittent Pilot Ignition

Valve Assembly

4

6

1

15

14

	2					5
	2
								9	12
						7		9
						7
						3	8	10	13
								10
								11
								11
ITEM /						DESCRIPTION		SERIAL #	PART NUMBER
PIÈCE						DESCRIPTION		/N° DE SÉRIE	/ N° DE PIÈCE
PIÈCE								/N° DE SÉRIE	/ N° DE PIÈCE
1	Burner Neck Gasket				/ Joint de Cou de Brûleur				2045-407
2	Thermostat Wire Assembly / L'Assemblée de Fil de thermostat								2045-024
3	Wire Assembly / Module de fil								2012-206
4	Pilot Assembly NG / Module de veilleuse GN								4021-025
4	Pilot Assembly LP / Module de veilleuse PL								4021-026
5	Valve Bracket	/	Parenthèse de Valve						2025-101
6	Ground Strap	/	Courroie de Raison(Terre)						385-512
7	Flex Ball Valve Assembly /					Fléchir l'Assemblée de Soupape de Balle			302-320A
8	Valve NG / Valve			GN					750-500
8	Valve LP / Valve			PL					750-501
9	Flexible Gas Connector /					Tuyau à gaz flexible			530-302A
10	Module / Module								593-592
11	Wire Assembly / Module de fil								593-590A
12	Battery Pack	/	Paquet de Batterie(Pile)						593-594A
13	3 Volt Transformer			/	3 Transformateur de Volt				593-593A
14	Valve Plate Gasket /				Joint de Plat de Valve				530-431
15	Pilot Bracket / Parenthèse Pilote								2065-117

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

11

Image 11

Contents SL-750TRS-IPI-D SL-550TRS-IPI-D SL-350TRS-C Installation and OperationSafety and Warning Information Table of Contents SL-350TRS-C Log Set AssemblySL-350TRS-C NG, LP Service Parts ListStanding Pilot Ignition Valve AssemblySL-550TRS-IPI-D SL-550TRS-IPI-D Part number list on following Log Set AssemblySL-750TRS-IPI-D Intermittent Pilot Ignition Valve Assembly Service Parts SL-750TRS-IPI-D, SL-550TRS-IPI-DCertification High Altitude InstallationsInstallation Codes Appliance CertificationManufacturer Requirements Requirements for the Commonwealth of MassachusettsVent Directly BELOW. Keep Clear of ALL OB- Structions ANY Such Action MAY Possibly Cause a Fire Hazard Pre-install PreparationIntroducing the Heat & Glo Gas Appliances Diagram of the SL-750TRS-IPI-D GAS Line Electrical Access Diagram of the SL-350TRS-C AccessClearance Requirements Constructing the Appliance ChaseLocating the Appliance Framing the Appliance Framing Dimensions34.93mm AT Each Joint 47 3/4 SL D-SERIES Components in ANY Vent Installing the Vent SystemSystem Configuration Identifying Vent ComponentsWith TWO 900 Elbows Flex VentStraight UP Vertical Venting Venting with One 90 Elbow Use SL D-Series components only Use DVP-Series Components onlyVenting with Two 90 Elbows Venting with TWO 2 90 o Elbows MAX. = 16 FT 4.8m + V 1 + H MAX. = 40 FT 12.2m Venting with Three 90 elbows Venting with Three 3 90 o Elbows + H 1 MAX. = 16 FT 4.8m + V 1 + H + H MAX. = 40 FT 12.2m Venting with Four 90 elbows DVP Series Venting Only Go to Install FirestopsAttach the First Vent Component to the Starting Collars SL-D and SL-Flex Series Venting OnlyHole and Vent Pipe DVP, SL-D and SL-Flex Series VentingFor All Venting Vent TerminationSL-Series Venting Only For DVP Venting OnlyVent Termination Minimum Clearances Alcove ApplicationsMinimum Height from Roof to Lowest Discharge Opening Millivolt System Positioning, Leveling, and Securing the ApplianceGas Control Systems Standing Pilot Ignition SystemPressure Natural Gas Propane Gas Supply LineGas Pressure Requirements Wall Switch Wiring the ApplianceFor Standing Pilot Ignition Wiring Appliance Requirements Optional AccessoriesIntermittent Pilot Ignition IPI Wiring Diagram Operation using Battery PowerNER FinishingPositioning the Logs Installing the TrimShutter Settings Glass SpecificationsLighting the Appliance After the InstallationDouble-check for faulty components Before Lighting the ApplianceImportant Turn OFF the GAS Before Servicing Your Appliance Appliance Maintenance