Heat & Glo LifeStyle SL-750TRS-IPI-D owner manual 34.93mm AT Each Joint

Page 20

4

6

12

DVP4

DVP6

DVP12

14-1/4

	12-3/16	2
	MAX.	2
	MAX.	MIN.
		MIN.
		24
	DVP12A	36

48

9-7/8	DVP24
	DVP24
	45.0O

10-1/4

DVP45

DVP36

11-1/4

7-1/4

1-1/4 TYP

DVP48

8-9/16

1/2 TYP

12-9/16

DVP90ST

NOTE: PIPES OVERLAP 1-1/4 INCHES

(34.93mm) AT EACH JOINT.

Figure 6. DVP-Series Direct Vent Component Specifications (5-inch inner pipe / 8-inch outer pipe)

20	Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

Image 20

Contents Installation and Operation SL-750TRS-IPI-D SL-550TRS-IPI-D SL-350TRS-CSafety and Warning Information Table of Contents Log Set Assembly SL-350TRS-CNG, LP Service Parts List SL-350TRS-CValve Assembly Standing Pilot IgnitionSL-550TRS-IPI-D SL-550TRS-IPI-D Log Set Assembly Part number list on followingSL-750TRS-IPI-D Service Parts SL-750TRS-IPI-D, SL-550TRS-IPI-D Intermittent Pilot Ignition Valve AssemblyHigh Altitude Installations Installation CodesAppliance Certification CertificationManufacturer Requirements Requirements for the Commonwealth of MassachusettsVent Directly BELOW. Keep Clear of ALL OB- Structions ANY Such Action MAY Possibly Cause a Fire Hazard Pre-install PreparationIntroducing the Heat & Glo Gas Appliances Diagram of the SL-750TRS-IPI-D GAS Line Electrical Access Access Diagram of the SL-350TRS-CClearance Requirements Constructing the Appliance ChaseLocating the Appliance Framing Dimensions Framing the Appliance34.93mm AT Each Joint 47 3/4 Installing the Vent System System ConfigurationIdentifying Vent Components SL D-SERIES Components in ANY VentWith TWO 900 Elbows Flex VentStraight UP Vertical Venting Use DVP-Series Components only Venting with One 90 Elbow Use SL D-Series components onlyVenting with Two 90 Elbows Venting with TWO 2 90 o Elbows MAX. = 16 FT 4.8m + V 1 + H MAX. = 40 FT 12.2m Venting with Three 90 elbows Venting with Three 3 90 o Elbows + H 1 MAX. = 16 FT 4.8m + V 1 + H + H MAX. = 40 FT 12.2m Venting with Four 90 elbows Go to Install Firestops DVP Series Venting OnlySL-D and SL-Flex Series Venting Only Attach the First Vent Component to the Starting CollarsDVP, SL-D and SL-Flex Series Venting Hole and Vent PipeVent Termination SL-Series Venting OnlyFor DVP Venting Only For All VentingAlcove Applications Vent Termination Minimum ClearancesMinimum Height from Roof to Lowest Discharge Opening Positioning, Leveling, and Securing the Appliance Gas Control SystemsStanding Pilot Ignition System Millivolt SystemPressure Natural Gas Propane Gas Supply LineGas Pressure Requirements Wiring the Appliance For Standing Pilot Ignition Wiring Appliance RequirementsOptional Accessories Wall SwitchOperation using Battery Power Intermittent Pilot Ignition IPI Wiring DiagramFinishing NERInstalling the Trim Shutter SettingsGlass Specifications Positioning the LogsAfter the Installation Double-check for faulty componentsBefore Lighting the Appliance Lighting the ApplianceAppliance Maintenance Important Turn OFF the GAS Before Servicing Your Appliance