Heat & Glo LifeStyle SL-750TRS-IPI-D owner manual SL-550TRS-IPI-D

Page 8

(NG, LP) Service Parts List

SL-550TRS-IPI-D

IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When ordering, supply serial and model numbers to ensure correct service parts.

ITEM	DESCRIPTION	SERIAL #	PART NUMBER

	Burner Orifice NG (#38C)		582-838

	Burner Orifice LP (#53C)		582-853

1	Junction Box		4021-013

2	Burner NG		2065-005

2	Burner LP		2065-006

3	Glass Door Assembly		GLA-550TRS

4	Log Grate		2066-036

5	Base Refractory NG, LP		2065-100

6	Hood		SRV550-175

7	Log Set Assembly		LOGS-550TRS-D

8	Log 1		SRV2065-701
9	Log 2		SRV2065-702

10	Log 3		SRV2065-703

11	Log 4		SRV2065-704

12	Log 5		SRV2065-705
	Refractory Kit		BRICK-550TRS-D

13	Refractory, Back		SRV2044-711

14	Refractory, Left Side		SRV2044-710

15	Refractory, Right Side		SRV2044-712

	Pilot Orifice NG		446-505

	Pilot Orifice LP		446-517

	Thermocouple		446-511

	Thermopile		060-512

	Mineral Wool		050-721

	Glass Latch		386-122A

	Exhaust Restrictor		530-299

	Touch up Paint		TUP-GBK-12

	ACCESSORIES
	Fan Kit		GFK-160A

	Extended Vertical Baffle Kit		BAF-VERT
	Wall Switch Kit, Off-white		WSK-21

	Wall Switch Kit, White		WSK-21-W

	Conversion Kit NG		NGK-550TRS-IPID

	Conversion Kit LP		LPK-550TRS-IPID
	Vermiculite Embers		MYSTIC-EMBERS

Í

Í

Í

Also see additional pages for valve assembly service part numbers.

8	Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

Image 8

Contents Installation and Operation SL-750TRS-IPI-D SL-550TRS-IPI-D SL-350TRS-CSafety and Warning Information Table of Contents Log Set Assembly SL-350TRS-CNG, LP Service Parts List SL-350TRS-CValve Assembly Standing Pilot IgnitionSL-550TRS-IPI-D SL-550TRS-IPI-D Log Set Assembly Part number list on followingSL-750TRS-IPI-D Service Parts SL-750TRS-IPI-D, SL-550TRS-IPI-D Intermittent Pilot Ignition Valve AssemblyHigh Altitude Installations Installation CodesAppliance Certification CertificationManufacturer Requirements Requirements for the Commonwealth of MassachusettsVent Directly BELOW. Keep Clear of ALL OB- Structions ANY Such Action MAY Possibly Cause a Fire Hazard Pre-install PreparationIntroducing the Heat & Glo Gas Appliances Diagram of the SL-750TRS-IPI-D GAS Line Electrical Access Access Diagram of the SL-350TRS-CClearance Requirements Constructing the Appliance ChaseLocating the Appliance Framing Dimensions Framing the Appliance34.93mm AT Each Joint 47 3/4 Installing the Vent System System ConfigurationIdentifying Vent Components SL D-SERIES Components in ANY VentWith TWO 900 Elbows Flex VentStraight UP Vertical Venting Use DVP-Series Components only Venting with One 90 Elbow Use SL D-Series components onlyVenting with Two 90 Elbows Venting with TWO 2 90 o Elbows MAX. = 16 FT 4.8m + V 1 + H MAX. = 40 FT 12.2m Venting with Three 90 elbows Venting with Three 3 90 o Elbows + H 1 MAX. = 16 FT 4.8m + V 1 + H + H MAX. = 40 FT 12.2m Venting with Four 90 elbows Go to Install Firestops DVP Series Venting OnlySL-D and SL-Flex Series Venting Only Attach the First Vent Component to the Starting CollarsDVP, SL-D and SL-Flex Series Venting Hole and Vent PipeVent Termination SL-Series Venting OnlyFor DVP Venting Only For All VentingAlcove Applications Vent Termination Minimum ClearancesMinimum Height from Roof to Lowest Discharge Opening Positioning, Leveling, and Securing the Appliance Gas Control SystemsStanding Pilot Ignition System Millivolt SystemPressure Natural Gas Propane Gas Supply LineGas Pressure Requirements Wiring the Appliance For Standing Pilot Ignition Wiring Appliance RequirementsOptional Accessories Wall SwitchOperation using Battery Power Intermittent Pilot Ignition IPI Wiring DiagramFinishing NERInstalling the Trim Shutter SettingsGlass Specifications Positioning the LogsAfter the Installation Double-check for faulty componentsBefore Lighting the Appliance Lighting the ApplianceAppliance Maintenance Important Turn OFF the GAS Before Servicing Your Appliance