Heat & Glo LifeStyle SL-750TRS-IPI-D owner manual NG, LP Service Parts List, SL-350TRS-C

Page 5

(NG, LP) Service Parts List

SL-350TRS-C

IMPORTANT: THIS IS DATED INFORMATION. The most current information is located on your dealers VIP site. When order- ing, supply serial and model numbers to ensure correct service parts.

	ITEM	STANDING PILOT		SERIAL #	PART NUMBER
		Burner Orifice NG (#43C)			582-843

		Burner Orifice LP (#53C)			582-853

	1	Glass Door Assembly			GLA-350TRS

	2	Burner NG, LP			540-234A

	3	Mesh Panel Door			540-382A

	4	Log Grate			540-361A

	5	Base Refractory	PRE	4/06	540-206T	(Tan)
	5	Base Refractory	POST	4/06	2065-206	(Black)
			POST	4/06	2065-206	(Black)
	6	Hood			SRV540-174

	7	Log Set Assembly			LOGS-350

	8	Log 1			SRV530-701

	9	Log 2			SRV530-704

	10	Log 3			SRV540-702

	11	Log 4			SRV530-705

	12	Log 5			SRV530-703

	13	Junction Box	PRE	00251404	100-250A
	13	Junction Box	POST	00251404	4021-013
			POST	00251404	4021-013
	14	Louver, Top			540-256A

	15	Louver, Bottom			540-257A

		Pilot Orifice NG			446-505

		Pilot Orifice LP			446-517

		Thermocouple			446-511

		Thermopile			060-512

		Conversion Kit NG			NGK-350TRS-C

		Conversion Kit LP			LPK-350TRS-C

		Vermiculite Embers			MYSTIC-EMBERS

		Exhaust Restrictor			530-299

		Glass Latch Assembly			386-122A

		Mineral Wool			050-721

		Touch up Paint			TUP-GBK-12

Also see additional pages for valve assembly service part numbers.

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

5

Image 5

Contents SL-750TRS-IPI-D SL-550TRS-IPI-D SL-350TRS-C Installation and OperationSafety and Warning Information Table of Contents SL-350TRS-C Log Set AssemblySL-350TRS-C NG, LP Service Parts ListStanding Pilot Ignition Valve AssemblySL-550TRS-IPI-D SL-550TRS-IPI-D Part number list on following Log Set AssemblySL-750TRS-IPI-D Intermittent Pilot Ignition Valve Assembly Service Parts SL-750TRS-IPI-D, SL-550TRS-IPI-DInstallation Codes High Altitude InstallationsAppliance Certification CertificationManufacturer Requirements Requirements for the Commonwealth of MassachusettsVent Directly BELOW. Keep Clear of ALL OB- Structions ANY Such Action MAY Possibly Cause a Fire Hazard Pre-install PreparationIntroducing the Heat & Glo Gas Appliances Diagram of the SL-750TRS-IPI-D GAS Line Electrical Access Diagram of the SL-350TRS-C AccessClearance Requirements Constructing the Appliance ChaseLocating the Appliance Framing the Appliance Framing Dimensions34.93mm AT Each Joint 47 3/4 System Configuration Installing the Vent SystemIdentifying Vent Components SL D-SERIES Components in ANY VentWith TWO 900 Elbows Flex VentStraight UP Vertical Venting Venting with One 90 Elbow Use SL D-Series components only Use DVP-Series Components onlyVenting with Two 90 Elbows Venting with TWO 2 90 o Elbows MAX. = 16 FT 4.8m + V 1 + H MAX. = 40 FT 12.2m Venting with Three 90 elbows Venting with Three 3 90 o Elbows + H 1 MAX. = 16 FT 4.8m + V 1 + H + H MAX. = 40 FT 12.2m Venting with Four 90 elbows DVP Series Venting Only Go to Install FirestopsAttach the First Vent Component to the Starting Collars SL-D and SL-Flex Series Venting OnlyHole and Vent Pipe DVP, SL-D and SL-Flex Series VentingSL-Series Venting Only Vent TerminationFor DVP Venting Only For All VentingVent Termination Minimum Clearances Alcove ApplicationsMinimum Height from Roof to Lowest Discharge Opening Gas Control Systems Positioning, Leveling, and Securing the ApplianceStanding Pilot Ignition System Millivolt SystemPressure Natural Gas Propane Gas Supply LineGas Pressure Requirements For Standing Pilot Ignition Wiring Appliance Requirements Wiring the ApplianceOptional Accessories Wall SwitchIntermittent Pilot Ignition IPI Wiring Diagram Operation using Battery PowerNER FinishingShutter Settings Installing the TrimGlass Specifications Positioning the LogsDouble-check for faulty components After the InstallationBefore Lighting the Appliance Lighting the ApplianceImportant Turn OFF the GAS Before Servicing Your Appliance Appliance Maintenance