Gas-Fired Products manual Typical Layouts PTU / PTS Series, Emitter Length Body Length Model

Page 12

7.0) TYPICAL LAYOUTS – PTU / PTS Series

10FT.

SYSTEM

50 FT.

SYSTEM

20 FT.

SYSTEM

30 FT.

SYSTEM

60 FT.

SYSTEM

40 FT.

SYSTEM

LEGEND		70 FT.
		70 FT.
Burner Box	5 FT. Body Section	SYSTEM
Flue Termination	90 Deg. Elbow
10 FT. Body Section	180 Deg. U-Bend

	EMITTER LENGTH			BODY LENGTH
MODEL	Min.	Max.	MODEL	Min.	Max.
PTS 40	10 Ft.	20 Ft.	PTU 40	10 Ft.	10 Ft.

PTS 50	20 Ft	30 Ft.	PTU 50	10 Ft.	15 Ft.

PTS 75	20 Ft.	30 Ft.	PTU 75	10 Ft.	15 Ft

PTS 100	30 Ft.	40 Ft.	PTU 100	15 Ft.	20 Ft.

PTS 125	30 Ft	50 Ft.	PTU 125	15 Ft.	25 Ft.

PTS 150	40 Ft.	60 Ft.	PTU 150	20 Ft.	30 Ft.

PTS 175	50 Ft.	70 Ft.	PTU 175	25 Ft.	35 Ft.

PTS 200	50 Ft.	70 Ft.	PTU 200	25 Ft.	35 Ft.

NOTES:

1)In all configurations, the control unit must be connected directly to either a) the 24-hole flange of the 10 ft. aluminized steel starting body section (for 10 ft., 20 ft., and 30 ft. systems) or b) the 6-hole flange of the 10 ft. alumi-therm steel starting body section (for 40 ft., 50 ft., 60 ft., and 70 ft. systems.

2)Joining of two 90º elbows directly together to form a “Z” shape IS NOT permitted.

3)PTS / U 175 - 40 ft length available for special applications.

4)5 Ft. Body Packages may be utilized on any of these heaters to yield heater lengths from 15 ft. to 70 ft.

5)Any configuration of components not shown in the illustrations may be used except as noted in 1 and 2

Form #43343330
May 08	–11–

Image 12

Contents Installation and Operation Instructions Table of Contents Safety Installer ResponsibilityInstallation Requirements General InformationFor Canada only High AltitudeMinimum Clearances to Combustibles Minimum Clearances to CombustiblesPTS/PTU Specifications Packing ListBurner Package Numbers Natural GASPTU 40-200 Body Package Descriptions Reflector, 4’ 11 ½’ Accessories End Reflector Accessory PackageExhaust Hood Package Typical Layouts PTU / PTS Series Emitter Length Body Length ModelTypical Assembly Layout Poisonous GAS and Soot HazardPTS Series Dimensions PTU Series Heater Assembly Joining of Tube SectionsTypical Assembly Overview PTU 40FT Shown Typical Suspension Methods Suspension HazardAssembly of Tube Sections CUT HazardAssembly of Extension Section MIN 8’ MAX 10’ Between HangersInserting Turbulators Assembly Hazard Adding ReflectorsAdding Optional 90º Elbow PTS only Adding Optional Corner Reflector PTS onlyAdding 180U-Bend PTU only Adding Optional U-BEND Reflector PTU onlyAttaching Burner BOX Assembly Connecting the Tiss System InstructionsEnd View Angle Mounted Heaters only GAS Connections and Regulations Do not USE AN Open Flame of ANY Kind to Test for LeaksKEY Dimensions and Components of the GAS Connections Instructions for Pressure Test Gauge Connection Supply PressureManifold Pressure Combination GAS Valve is Factory SET Electrical Connections STEP-OPENING GAS Control ValveIgnition Module Terminal Designations 24VAC/R TH/WPS/W GNDLine Voltage 120V Thermostat Connections Single Heater Line Voltage 120V Thermostat Connections Multiple HeatersLOW Voltage 24V Thermostat Connections Single Heaters Venting Carbon Monoxide HazardSingle Heater Venting Vertical Through the Roof Single Heater Venting Horizontal Through Sidewall#10 Self-Drill Vent Pipe Screws Multiple Heater Vertical venting arrangement PTS/PTU Common Vent DiameterAIR for Combustion Direct Outside AIR for CombustionVertical Lighting and Shutdown Instructions Sequence of OperationBurner Component Locations Cleaning and Maintenance Electric Shock & Explosion HazardTroubleshooting Guide Form Form #43343330 May Replacing Parts Removal of Main Burner and ElectrodesRemoval of GAS Valve and Manifold Assembly AIR Switch Pressure CheckIgnition System Checks To Check Flame Sensor CircuitInstallation Data Ignition Module DiagnosticsReplacement Parts Guide Burner BOX FastenersLabels/Manual 22c 22b 22a 40a 17a Body Components Description