Gas-Fired Products PTS Series manual Assembly of Extension Section, MIN 8’ MAX 10’ Between Hangers

Page 20

10.1ASSEMBLY OF EXTENSION SECTION

MIN 8’ MAX 10’ BETWEEN HANGERS

Coupling

2

3

Tube Support/

1

Wire Hanger

U-Bolt Clamp

& 5/16” Hex Nuts

Hanger BracketTube Support/ Hanger Bracket

6” approx.

See typical assembly overview (Section 8.0) for typical complete assembly. Assemble additional extension sections as required for all systems. (See Sections 7.0, and 8.0 for typical layout details.)

Join the tube sections together and secure with tube couplings as described below:

WARNING: THE FOLLOWING COUPLING TIGHTENING INSTRUCTIONS MUST BE FOLLOWED PROPERLY TO AVOID FUTURE PROBLEMS.

1.Place the compression coupling over the end of the tube.

2.Use the small hole at the centerline of the coupling to check that the coupling is inserted correctly.

3.Partially tighten the bolt nearest the end of the tube (approximately half closed).

1
Tube
Center end of
Tube with hole
Tube
Coupling	3
Partially tighten this bolt	3

2

Form #43343330
May 08	–19–

Image 20

Contents Installation and Operation Instructions Table of Contents Safety Installer ResponsibilityInstallation Requirements General InformationFor Canada only High AltitudePTS/PTU Minimum Clearances to CombustiblesMinimum Clearances to Combustibles Specifications Packing ListBurner Package Numbers Natural GASPTU 40-200 Body Package Descriptions Reflector, 4’ 11 ½’ Accessories End Reflector Accessory PackageExhaust Hood Package Typical Layouts PTU / PTS Series Emitter Length Body Length ModelTypical Assembly Layout Poisonous GAS and Soot HazardPTS Series Dimensions PTU Series Heater Assembly Joining of Tube SectionsTypical Assembly Overview PTU 40FT Shown Typical Suspension Methods Suspension HazardAssembly of Tube Sections CUT HazardAssembly of Extension Section MIN 8’ MAX 10’ Between HangersInserting Turbulators Assembly Hazard Adding ReflectorsAdding Optional 90º Elbow PTS only Adding Optional Corner Reflector PTS onlyAdding 180U-Bend PTU only Adding Optional U-BEND Reflector PTU onlyAttaching Burner BOX Assembly Connecting the Tiss System InstructionsEnd View Angle Mounted Heaters only GAS Connections and Regulations Do not USE AN Open Flame of ANY Kind to Test for LeaksKEY Dimensions and Components of the GAS Connections Manifold Pressure Combination GAS Valve is Factory SET Instructions for Pressure Test Gauge ConnectionSupply Pressure Electrical Connections STEP-OPENING GAS Control ValveIgnition Module Terminal Designations 24VAC/R TH/WPS/W GNDLOW Voltage 24V Thermostat Connections Single Heaters Line Voltage 120V Thermostat Connections Single HeaterLine Voltage 120V Thermostat Connections Multiple Heaters Venting Carbon Monoxide HazardSingle Heater Venting Vertical Through the Roof Single Heater Venting Horizontal Through Sidewall#10 Self-Drill Vent Pipe Screws Multiple Heater Vertical venting arrangement PTS/PTU Common Vent DiameterAIR for Combustion Direct Outside AIR for CombustionVertical Lighting and Shutdown Instructions Sequence of OperationBurner Component Locations Cleaning and Maintenance Electric Shock & Explosion HazardTroubleshooting Guide Form Form #43343330 May Replacing Parts Removal of Main Burner and ElectrodesRemoval of GAS Valve and Manifold Assembly AIR Switch Pressure CheckIgnition System Checks To Check Flame Sensor CircuitInstallation Data Ignition Module DiagnosticsReplacement Parts Guide Burner BOX FastenersLabels/Manual 22c 22b 22a 40a 17a Body Components Description