Gas-Fired Products PTS Series, PTU Series KEY Dimensions and Components of the GAS Connections

Page 30

KEY DIMENSIONS AND COMPONENTS OF THE GAS CONNECTIONS

Approved

Flexible Connector

14 to 17”

2” (5cm) Max.

(36 to 43cm)

Displacement

 

 

 

 

 

 

 

 

 

 

 

 

 

* Available as Accessories

Gas Pressure

= 2 PSIG

Gas Supply

Piping

*Manual Gas

Shut Off Valve

Sediment Trap

(Drip Leg)

*Second Stage Regulator with Vent Leak Limiter to reduce the Supply Pressure below 14” W.C.

Burner Movement

RECOMMENDED GAS CONNECTION POSITIONS WITH 36” FLEXIBLE GAS HOSE

Alternate Positions

7 5/8”

6”

DO NOT install gas connector

vertically if fresh air is to be Adaptor 1/2” NPT male connected.

3 7/8” (10cm)

 

Adaptor 1/2” NPT female

 

Gas pipe work must not restrict

END VIEW

opening of hinged service doors.

 

Minimum 1” (25cm)

Burner Movement

SIDE VIEW

Certified connectors are recommended to be installed as shown, in one plane, and without sharp bends, kinks or twists.

INCORRECT POSITIONS

MovementMovement

WRONG

 

Movement

Movement

WRONG

WRONG

WRONG

Form #43343330

 

May 08

–29–

Image 30
Contents Installation and Operation Instructions Table of Contents Installation Requirements SafetyInstaller Responsibility General InformationFor Canada only High AltitudeMinimum Clearances to Combustibles Minimum Clearances to CombustiblesPTS/PTU Specifications Packing ListBurner Package Numbers Natural GASPTU 40-200 Body Package Descriptions Reflector, 4’ 11 ½’ Accessories End Reflector Accessory PackageExhaust Hood Package Typical Layouts PTU / PTS Series Emitter Length Body Length ModelTypical Assembly Layout Poisonous GAS and Soot HazardPTS Series Dimensions PTU Series Heater Assembly Joining of Tube SectionsTypical Assembly Overview PTU 40FT Shown Typical Suspension Methods Suspension HazardAssembly of Tube Sections CUT HazardAssembly of Extension Section MIN 8’ MAX 10’ Between HangersInserting Turbulators Assembly Hazard Adding ReflectorsAdding Optional 90º Elbow PTS only Adding Optional Corner Reflector PTS onlyAdding 180U-Bend PTU only Adding Optional U-BEND Reflector PTU onlyAttaching Burner BOX Assembly Connecting the Tiss System InstructionsEnd View Angle Mounted Heaters only GAS Connections and Regulations Do not USE AN Open Flame of ANY Kind to Test for LeaksKEY Dimensions and Components of the GAS Connections Instructions for Pressure Test Gauge Connection Supply PressureManifold Pressure Combination GAS Valve is Factory SET Electrical Connections STEP-OPENING GAS Control ValvePS/W Ignition Module Terminal Designations 24VAC/RTH/W GNDLine Voltage 120V Thermostat Connections Single Heater Line Voltage 120V Thermostat Connections Multiple HeatersLOW Voltage 24V Thermostat Connections Single Heaters Venting Carbon Monoxide HazardSingle Heater Venting Vertical Through the Roof Single Heater Venting Horizontal Through Sidewall#10 Self-Drill Vent Pipe Screws Multiple Heater Vertical venting arrangement PTS/PTU Common Vent DiameterAIR for Combustion Direct Outside AIR for CombustionVertical Lighting and Shutdown Instructions Sequence of OperationBurner Component Locations Cleaning and Maintenance Electric Shock & Explosion HazardTroubleshooting Guide Form Form #43343330 May Replacing Parts Removal of Main Burner and ElectrodesRemoval of GAS Valve and Manifold Assembly AIR Switch Pressure CheckIgnition System Checks To Check Flame Sensor CircuitInstallation Data Ignition Module DiagnosticsReplacement Parts Guide Burner BOX FastenersLabels/Manual 22c 22b 22a 40a 17a Body Components Description