Regency L676 installation manual Conversion KIT #521-969 from NG to LP

Page 28

INSTALLATION

INSTALLATION

CONVERSION KIT #521-969 FROM NG TO LP

LP Conversion instructions for BEFORE UNIT INSTALLATION.

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER, IF IN DOUBT DO NOT DO THIS CONVERSION!!

LP Conversion Kit Contains:

Qty.	Part #	Description
1	910-462	LP Conversion Coil
1	904-573	Cable Tie
1	910-037	LP Pilot Oriﬁce
1	904-345	Oriﬁce #53 (back)
1	904-241	Oriﬁce #56 (front)
1	904-529	Allen Key
1	918-590	LP Conversion Decal
1	908-528	Red Propane Label

1918-596 Instruction Sheet

1)Remove the glass door.

a.Release the 2 door latches on the left and right side at the top of the ﬁrebox.

b. Swing the door out from the top and release the hinges on the left and right side of the door by lifting them up.

Hinge

Door

		Front Burner Removed
	c. Place the door on a soft surface to prevent	4) Remove the back burner by removing the
	c. Place the door on a soft surface to prevent	screw.
	scratching.	screw.
	scratching.
	2) Remove the grate by undoing the 2 screws
	on the right and left side.

Latch Location

Latch

Grate

3) Remove the front burner by removing the screw.

Back Burner

5)Remove the rear log stand by removing the 4 screws.

Rear Log Stand

Front Burner

28	Regency® L676 Direct Vent Gas Fireplace

Image 28

Contents Libertytm L676 Gas Fireplace Manufactured Mobile Home Requirements Table of Contents Safety Label Copy of Safety DecalRequirements MA Code CO DetectorUnit Dimensions Installation General Safety InformationInstallation Checklist Important Message Save These InstructionsHeat Release KIT Hearth RequirementsManufactured Mobile Home Additional Requirements Locating Your GAS FireplaceClearances Mantel Clearances Mantel LEG ClearancesFraming & Finishing Important Header must be metal studUnit Assembly Prior to InstallationVenting Introduction Vent Restrictor PositionFactory set for NG units Factory set for LP unitsExterior Vent Termination Requirements Venting Arrangements FPI Kit # Length ContainsInstallation Rigid Pipe Venting Systems8 Rigid Pipe Cross Reference Chart 58DVA-16ABL676 & L900 Direct Vent Fireplace Allowable Horizontal Terminations Horizontal Venting with Two 2 90o Elbows Vertical Venting with Two 2 90o Elbows Vent must be supported at offsets Feet HeightUnit Installation with Horizontal Termination Unit Installation With Vertical Termination This allows for small adjustmentsDiagram Minimum VentUnit Installation Horizontal Termination with Flex Vent SystemGAS Line BACK-UP Battery Installation Hinge Door Heat Shield Power ModulePower Module Heat Shield Latch LocationConversion KIT #521-969 from NG to LP Pilot ShieldHeat Using a ﬂat head screw driverClip Heat Shield J9 Jumper Location J9 JumperHeat Shield Front Burner Bracket Heat Shield Front Burner RemovedHinge Door Rear Log Stand GrateModulating Coil Wires Bottom Brick PanelHeat Shield Bracket Heat ShieldClip Pilot ShieldCable Tie Brick Panel Installation Handle with care. do not Force Into PositionOuterbox of Firebox Bracket Brick Panel Clip Tab Base Brick Panel SlotRear Burner Tube Front Burner Tube LOG SET InstallationBackside of Grate Complete Log Set Installation Aeration Adjustment Wiring DiagramLighting Procedure Operating InstructionsMatching Remote Handset & Control BOX ID Code Operating InstructionsOperation During Power Outage Shutdown ProcedureNormal Operating Sounds GAS Appliances GAS Control Valve Copy of Lighting Plate InstructionsRight Side Exterior Brick Panel Heat ShieldMaintenance BACK-UP Battery Replacement Bracket Hinge Heat DoorPower Module Replacement Bracket Heat ShieldBracket Hinge Heat Control Module ReplacementControl Module Battery Cover DC Sparker ReplacementHeat Shield Replace the DC sparker Valve Tray Replacement Unplug the power sourceValve Carefully remove the bottom brick panelModulating coil Main Assembly Parts ListDescription Parts List Burner & LOG Assembly Parts List Parts List Parts List Warranty Warranty Limited LifetimeInstaller Please complete the following information