Regency L676 installation manual Parts List, Main Assembly, Description

Page 49

PARTS LIST

MAIN ASSEMBLY

Part #		Description
1)	521-527	Flue Collar Inner Assembly
2)	502-008	Flue Collar Outer
5)	904-732	Cap Screws 1/4" x 2-3/4"
6)	W260280	Gasket Top Relief Plate
7)	770-066F	Top Relief Plate
8)	942-117	Top Relief Frame
9)	W260260	Top Relief Frame Gasket
11) 521-064		Heat Shield ECS
12) 521-540		Door Frame Assembly with Glass
	940-351/P	Glass
13) 521-013		One Piece Faceplate
15) 521-021F		Control Arm
16)	521-019	Bracket Control Arm

17)521-065 Heat Shield Valve

18)521-024 Gas Line Screen Plate

20)521-901 Brick Panel Set - Standard Brown

521-902 Brick Panel Set - Standard Red

*Left Side Panel (Interior)

*Top Panel (Interior)

*Back Panel (Interior)

*Right Side Panel (Interior)

*Right Side Panel (Exterior)

*Base Panel (Exterior)

*Left Side Panel (Exterior)

946-556	Heat Wave Kit
946-570	Heat Release Kit
521-969	LP Converison Kit
918-568	Manual

* Not available as a replacement part.

PARTS LIST

Regency® L676 Direct Vent Gas Fireplace

49

Image 49

Contents Libertytm L676 Gas Fireplace Manufactured Mobile Home Requirements Table of Contents Copy of Safety Decal Safety LabelMA Code CO Detector RequirementsUnit Dimensions General Safety Information InstallationInstallation Checklist Important Message Save These InstructionsHearth Requirements Heat Release KITManufactured Mobile Home Additional Requirements Locating Your GAS FireplaceClearances Mantel LEG Clearances Mantel ClearancesImportant Header must be metal stud Framing & FinishingPrior to Installation Unit AssemblyVent Restrictor Position Venting IntroductionFactory set for NG units Factory set for LP unitsExterior Vent Termination Requirements FPI Kit # Length Contains Venting ArrangementsRigid Pipe Venting Systems Installation58DVA-16AB 8 Rigid Pipe Cross Reference ChartL676 & L900 Direct Vent Fireplace Allowable Horizontal Terminations Horizontal Venting with Two 2 90o Elbows Vertical Venting with Two 2 90o Elbows Feet Height Vent must be supported at offsetsUnit Installation with Horizontal Termination This allows for small adjustments Unit Installation With Vertical TerminationDiagram Minimum VentHorizontal Termination with Flex Vent System Unit InstallationGAS Line Hinge Door Heat Shield Power Module BACK-UP Battery InstallationPower Module Heat Shield Latch LocationConversion KIT #521-969 from NG to LP Pilot ShieldHeat Using a ﬂat head screw driverClip Heat Shield J9 Jumper J9 Jumper LocationBracket Heat Shield Front Burner Removed Heat Shield Front BurnerHinge Door Rear Log Stand GrateBottom Brick Panel Modulating Coil WiresHeat Shield Bracket Heat ShieldClip Pilot ShieldCable Tie Handle with care. do not Force Into Position Brick Panel InstallationBracket Brick Panel Clip Tab Base Brick Panel Slot Outerbox of FireboxRear Burner Tube Front Burner Tube LOG SET InstallationBackside of Grate Complete Log Set Installation Wiring Diagram Aeration AdjustmentOperating Instructions Lighting ProcedureMatching Remote Handset & Control BOX ID Code Operating InstructionsOperation During Power Outage Shutdown ProcedureNormal Operating Sounds GAS Appliances Copy of Lighting Plate Instructions GAS Control ValveRight Side Exterior Brick Panel Heat ShieldMaintenance Bracket Hinge Heat Door BACK-UP Battery ReplacementBracket Heat Shield Power Module ReplacementBracket Hinge Heat Control Module ReplacementControl Module Battery Cover DC Sparker ReplacementHeat Shield Replace the DC sparker Unplug the power source Valve Tray ReplacementValve Carefully remove the bottom brick panelModulating coil Main Assembly Parts ListDescription Parts List Burner & LOG Assembly Parts List Parts List Parts List Warranty Limited Lifetime WarrantyInstaller Please complete the following information