Regency L676 installation manual Burner & LOG Assembly

Page 51

PARTS LIST

BURNER & LOG ASSEMBLY

	Part #	Description
30)	521-015	Bracket Log Tray
31)	521-016	Log Tray
32)	521-042	Deﬂ ector Log Tray

35)948-455 Burner Rear NG/LP

36)948-454 Burner Front NG/LP

37)521-050 Grate

40)	521-063	Bracket Log Position
41)	502-061	Pilot Shield
42)	380-013	Pilot Holder
43)	W840470	Gasket Pilot Assembly
46)	521-007	Valve Tray
47)	521-025	Valve Bracket

48)910-460 Valve NG 825 SIT Electric

521-574/P Valve Assembly - NG

521-576/P Valve Assembly - LP

910-008	Pilot Assembly - NG
910-009	Pilot Assembly - LP
904-617	Oriﬁ ce #34
904-622	Oriﬁ ce #48
910-937	Valve Solenoid
910-929	Control Module
910-931	Power Module
910-930	FireWizardTM Remote Control
918-582	Manual FireWizardTM

PARTS LIST

Regency® L676 Direct Vent Gas Fireplace

51

Image 51

Contents Libertytm L676 Gas Fireplace Manufactured Mobile Home Requirements Table of Contents Copy of Safety Decal Safety LabelMA Code CO Detector RequirementsUnit Dimensions Important Message Save These Instructions InstallationGeneral Safety Information Installation ChecklistLocating Your GAS Fireplace Heat Release KITHearth Requirements Manufactured Mobile Home Additional RequirementsClearances Mantel LEG Clearances Mantel ClearancesImportant Header must be metal stud Framing & FinishingPrior to Installation Unit AssemblyFactory set for LP units Venting IntroductionVent Restrictor Position Factory set for NG unitsExterior Vent Termination Requirements FPI Kit # Length Contains Venting ArrangementsRigid Pipe Venting Systems Installation58DVA-16AB 8 Rigid Pipe Cross Reference ChartL676 & L900 Direct Vent Fireplace Allowable Horizontal Terminations Horizontal Venting with Two 2 90o Elbows Vertical Venting with Two 2 90o Elbows Feet Height Vent must be supported at offsetsUnit Installation with Horizontal Termination Minimum Vent Unit Installation With Vertical TerminationThis allows for small adjustments DiagramHorizontal Termination with Flex Vent System Unit InstallationGAS Line Heat Shield Latch Location BACK-UP Battery InstallationHinge Door Heat Shield Power Module Power ModuleConversion KIT #521-969 from NG to LP Using a ﬂat head screw driver Pilot ShieldHeatClip Heat Shield J9 Jumper J9 Jumper LocationRear Log Stand Grate Heat Shield Front BurnerBracket Heat Shield Front Burner Removed Hinge DoorBracket Heat Shield Modulating Coil WiresBottom Brick Panel Heat ShieldPilot Shield ClipCable Tie Handle with care. do not Force Into Position Brick Panel InstallationBracket Brick Panel Clip Tab Base Brick Panel Slot Outerbox of FireboxLOG SET Installation Rear Burner Tube Front Burner TubeBackside of Grate Complete Log Set Installation Wiring Diagram Aeration AdjustmentOperating Instructions Lighting ProcedureOperating Instructions Matching Remote Handset & Control BOX ID CodeShutdown Procedure Operation During Power OutageNormal Operating Sounds GAS Appliances Heat Shield GAS Control ValveCopy of Lighting Plate Instructions Right Side Exterior Brick PanelMaintenance Bracket Hinge Heat Door BACK-UP Battery ReplacementBracket Heat Shield Power Module ReplacementControl Module Replacement Bracket Hinge HeatControl Module DC Sparker Replacement Battery CoverHeat Shield Replace the DC sparker Unplug the power source Valve Tray ReplacementCarefully remove the bottom brick panel ValveModulating coil Parts List Main AssemblyDescription Parts List Burner & LOG Assembly Parts List Parts List Parts List Warranty Limited Lifetime WarrantyInstaller Please complete the following information