Regency L676 installation manual Control Module Replacement, Bracket Hinge Heat

Page 45

MAINTENANCE

CONTROL MODULE REPLACEMENT

1) Remove the exterior brick panels.

3) Loosen the 2 screws that hold the left side

7) Disconnect the 3 connectors from the

 

heat shield in place.

control module.

2)Remove the glass door.

a.Release the 2 door latches on the left and right side at the top of the fi rebox.

Heat

Shield

Latch Location

Latch

8)Pull out the control module.

b.Swingthedooroutfromthetopandrelease the hinges on the left and right side of the door by lifting them up.

4)Lift up and pull out the heat shield slightly to clear the screwheads and then hang it on the top bracket (located directly above the heat shield).

Bracket

NOTE: The control module is held in place with velcro.

Hinge

Heat

Shield

Door

 

9) Replace the control module

5)Unplug the power source.

10) Reverse steps to re-install.

6)Cut the cable tie that is holds the wires connected to the control module.

Control Module

MAINTENANCE

Regency® L676 Direct Vent Gas Fireplace

45

Image 45
Contents Libertytm L676 Gas Fireplace Manufactured Mobile Home Requirements Table of Contents Copy of Safety Decal Safety LabelMA Code CO Detector RequirementsUnit Dimensions General Safety Information InstallationInstallation Checklist Important Message Save These InstructionsHearth Requirements Heat Release KITManufactured Mobile Home Additional Requirements Locating Your GAS FireplaceClearances Mantel LEG Clearances Mantel ClearancesImportant Header must be metal stud Framing & FinishingPrior to Installation Unit AssemblyVent Restrictor Position Venting IntroductionFactory set for NG units Factory set for LP unitsExterior Vent Termination Requirements FPI Kit # Length Contains Venting ArrangementsRigid Pipe Venting Systems Installation58DVA-16AB 8 Rigid Pipe Cross Reference ChartL676 & L900 Direct Vent Fireplace Allowable Horizontal Terminations Horizontal Venting with Two 2 90o Elbows Vertical Venting with Two 2 90o Elbows Feet Height Vent must be supported at offsetsUnit Installation with Horizontal Termination This allows for small adjustments Unit Installation With Vertical TerminationDiagram Minimum VentHorizontal Termination with Flex Vent System Unit InstallationGAS Line Hinge Door Heat Shield Power Module BACK-UP Battery InstallationPower Module Heat Shield Latch LocationConversion KIT #521-969 from NG to LP Using a flat head screw driver Pilot ShieldHeatClip Heat Shield J9 Jumper J9 Jumper LocationBracket Heat Shield Front Burner Removed Heat Shield Front BurnerHinge Door Rear Log Stand GrateBottom Brick Panel Modulating Coil WiresHeat Shield Bracket Heat ShieldPilot Shield ClipCable Tie Handle with care. do not Force Into Position Brick Panel InstallationBracket Brick Panel Clip Tab Base Brick Panel Slot Outerbox of FireboxLOG SET Installation Rear Burner Tube Front Burner TubeBackside of Grate Complete Log Set Installation Wiring Diagram Aeration AdjustmentOperating Instructions Lighting ProcedureMatching Remote Handset & Control BOX ID Code Operating InstructionsShutdown Procedure Operation During Power OutageNormal Operating Sounds GAS Appliances Copy of Lighting Plate Instructions GAS Control ValveRight Side Exterior Brick Panel Heat ShieldMaintenance Bracket Hinge Heat Door BACK-UP Battery ReplacementBracket Heat Shield Power Module ReplacementControl Module Replacement Bracket Hinge HeatControl Module DC Sparker Replacement Battery CoverHeat Shield Replace the DC sparker Unplug the power source Valve Tray ReplacementCarefully remove the bottom brick panel ValveModulating coil Parts List Main AssemblyDescription Parts List Burner & LOG Assembly Parts List Parts List Parts List Warranty Limited Lifetime WarrantyInstaller Please complete the following information