Brother UM 103D manual To Do Rolled Edge Stitch, To Do Narrow Overlock Stitch

Page 51

(6)Adjust the stitch length.

 

(6)Ajuste el largo de las puntadas.

Set the stitch length adjustment lever to “R”

 

Coloque la palanca de ajuste del largo de las

position as shown in the illustration. This adjust-

 

puntadas en la posición “R” tal como lo muestra

ment is suitable for either Narrow Overlock stitch

 

la ilustración. Este ajuste conviene tanto para las

or Rolled Edge stitch.

 

puntadas overlock estrechas como para las de

 

 

dobladillo enrollado.

 

 

 

2 3 4

R

TABLE OF CONTENTS

Chapter 1

Chapter 2

Chapter 3

Chapter 4

Chapter 5

Chapter 6

Chapter 7

To Do Rolled Edge Stitch

This application rolls the edge of the fabric inside of the hem stitch. The lowerlooper tension should be tightened. This pulls the upperlooper thread causing the edge of the fabric to fold around the remaining stitch finger. After completing steps (1) through (6) above, adjust your machine to these recommended thread tension settings:

Upperlooper thread tension at 1-4 Lowerlooper thread tension at 5-7 Right needle thread tension at 4

Tension may vary slightly according to the fabric and thread used.

To Do Narrow Overlock Stitch

This is a decorative application used for finishing the edge of the fabric. After completing steps (1) through

(6)above, adjust the thread tension to achieve a normal 3-thread overlock stitch.

Recommended thread tension settings are:

All thread tensions should be set at 4

Tension may vary slightly according to the fabric and thread used.

Para realizar puntadas de borde enrollado

Esta función permite meter el borde del tejido en las puntadas de dobladillo. Para poder realizarlo, con- viene aumentar la tensión del áncora inferior. Así, se tira del hilo del áncora superior y el borde del tejido se dobla alrededor de la uñeta remanente. Después de implementar las operaciones (1) a (6) indicadas arriba, se recomienda ajustar la máquina en los siguientes valores de tensión de hilo:

Tensión del hilo del áncora superior entre 1-4 Tensión del hilo del áncora inferior entre 5-7 Tensión del hilo de la aguja derecha en 4.

La tensión puede variar ligeramente según los teji dos e hilos utilizados.

Para realizar puntadas overlock estrechas Esta función decorativa conviene para mejor termi- nar el borde del tejido. Después de los puntos (1) a

(6)indicados arriba, ajuste las tensiones de los hilos con vistas a lograr una puntada overlock normal de tres hilos. Los ajustes de tensión recomendados son:

Todas las tensiones de los hilos deben estar en 4. La tensión puede variar dependiendo de los tejidos e hilos utilizados.

Chapter 8

Chapter 9

10

Chapter

11

Chapter

12

Chapter

13

Chapter

14

Chapter

15

Chapter

16

Chapter

17

Chapter

18

Chapter

44

Image 51
Contents Handbook for Compact Overlock Machine Important Safety Instructions For Users in the UK, EIRE, Malta and Cyprus only Congratulations on Choosing this Compact Overlock Machine Notas Sobre EL Motor Table of Contents Especificaciones técnicas de la máquina Funcionamiento Encendido de la máquinaEngrasado Cambio de la bombilla de luzNames of parts Nombres de las partesSus funciones Contents La máquina de coser Accessories includedAccesorios incluidos con With your sergerXA6410051 Australia, Nueva Zelanda XA6420051 Alemania Para introducir la aguja NeedleAguja Para sacar la agujaModelos de una aguja Two-needle modelsModelos de dos agujas One-needle modelsTurning direction of motor Opening and closing Front coverAbre y cierre de la tapa Delantera Encendido de la máquina Powering the machineOperating FuncionamientoRemoving Bed Extension for Free-Arm Sewing Removing the bed extensionExtraiga el suplemento Para la mesa Ancho de puntada Stitch LengthLargo de puntada Stitch WidthInstrucciones para el Tight Ción con diferencial, su borde va a ser oleado ∙ Ejemplo en que se requiere ajustePreparación antes del enhebrado Before ThreadingAntes del enhebrado Preparation before ThreadingComo utilizar el tope del Carrete Como utilizar la malla Para hiloBotón de liberación de la tensión Antes de enhebrar Before threadingEnhebrado del áncora superior Threading UpperlooperSi el hilo del áncora superior se rompe al coser If the upperlooper thread breaks during sewingEnhebrado del áncora inferior Threading LowerlooperPrecauciones Enhebrado de la aguja derecha los modelos de dos agujas Threading the right Needle on Two-needle ModelsContents Enhebrado de la aguja Izquierda Threading the left needleContents Material Stitch Stitch Length Thread Needle Comparison Chart of Sewing Materials, Threads and NeedlesCrepe de China Hilo de Tejido Puntada Largo de Hilo Aguja Puntada mmDisco de tensión del hilo Thread TensionTensión del hilo Thread tension dialAjuste de la tensión del hilo Adjusting the thread tensionTension control Para controlar la tensiónChart of Thread Tension Adjustment Two-needle Four-thread Order of thread tension adjustment Orden de ajuste de tensión de los hilosEn el orden siguiente One-needle Three-thread El hilo de la aguja está sueltoFrunces Una aguja tres hilos Costura de prueba Test-sewingCadeneta Chaining-offPara empezar a coser SewingCostura To start sewingSi el hilo se rompe al Coser To remove workIf threads break during Sewing Para retirar el trabajoPara coser tejidos finos To sew heavy materialsTo sew fine materials Para coser tejidos gruesosPresión del prensatelas Presser foot pressureTrouble Cause Remedy TroubleshootingGuía de localización de fallas Problema Causa RemedioPuntadas Overlock estrechas, de dobladillo enrollado ,0 mm Stitch SelectionSelección de las distintas puntadas Puntada Overlock de cuatro hilosInstructions for both Narrow overlock/Rolled edge Stitches Narrow overlock stitch Rolled edge stitchTwo-needle models B One-needle models To Do Rolled Edge Stitch To Do Narrow Overlock StitchPara realizar puntadas de borde enrollado Rolled edge stitch Narrow overlock stitch Chart of Narrow Overlock/Rolled Edge StitchPuntada de borde enrollado Puntada overlock estrecha Tabla para puntadas overlock estrechas/de borde enrolladoComo cambiar los prensatelas FeaturesHow to change feet CaracterísticasDe dos agujas ∙ Se debe retirar la aguja derecha Blind stitching with blind Stitch presser footPuntadas invisibles con Multipropósito véase páginaTensión del hilo de la aguja bastante floja Los ajustes recomendados son los siguientesMm Modelos de una aguja Largo de puntada 3 4 mmFlatlock stitching with blind stitch presser foot Costura Overlock plana Con prensatelas multipropósitoDe dos agujas Tensión del hilo del áncora superior ∙ Este método no conviene para tejidos finosLargo de puntada 2 ~ 4 mm Tensión del hilo de la agujaPin tuck stitching with blind stitch presser foot Guide and the thread tension Test sew on a scrap of the fabric to adjust the fabricOtros prensatelas especiales disponibles Decorative stitchingPuntadas decorativas Other special purpose presser feet that are avail- ableMeter la cuchilla superior Upper Knife Lower KnifeCuchillas superior e Inferior Retracting upper knifeCambio de la cuchilla inferior Replacing the knivesCambio de las cuchillas Cambio de la cuchilla superiorOiling EngrasadoPuntos de engrasado sugeridos Cambio de la bombilla De luz Changing the Light BulbEspecificaciones técni Cas de la máquina Machine SpecificationsTipo de Setting Record / Notas DE Ajustes1034D 193345-011

UM 103D specifications

The Brother UM 103D is a versatile and user-friendly sewing machine designed to cater to both beginners and experienced sewers. This model blends simplicity with a range of features that allow for the creation of diverse sewing projects, making it an excellent addition to any sewing room.

One of the standout characteristics of the Brother UM 103D is its lightweight and compact design. Weighing in at just a few pounds, this machine is easily portable, making it ideal for those who wish to take their sewing projects to classes or retreats. Its sleek design and bright color options also enhance its aesthetic appeal, attracting a wide range of users.

Equipped with a powerful motor, the UM 103D can handle various fabrics, from lightweight cotton to heavier materials like denim. It features adjustable stitch length and width, allowing users to customize their sewing experience according to project requirements. Additionally, the machine comes with a selection of built-in stitches, including essential utility stitches, decorative stitches, and stretch stitches, adding versatility to creative projects.

One of the technological advancements in the Brother UM 103D is its easy threading system. The machine is designed for effortless bobbin winding and threading, which is particularly beneficial for beginners who may find traditional sewing machines intimidating. The quick-set bobbin system helps reduce downtime, allowing users to spend more time sewing and less time on setup.

The Brother UM 103D also features a free arm design, which is perfect for sewing cylindrical items such as sleeves and pant legs. This design enhances accessibility and ease of working on complex projects. In addition, the machine is equipped with an automatic needle threader, simplifying the threading process and reducing eye strain.

For those who like to experiment with embellishments, the UM 103D supports a variety of presser feet, enabling users to perform tasks like quilting, zipper insertion, and buttonholing with ease. Its wide accessory package includes multiple presser feet, a seam ripper, and a variety of needles, making it a comprehensive package for sewing enthusiasts.

Overall, the Brother UM 103D is an excellent sewing machine that combines portability, ease of use, and advanced features. Its user-friendly design, solid construction, and range of capabilities make it suitable for a wide array of sewing projects, providing both new and experienced sewists with the tools needed to express their creativity.