Alto-Shaam QC-3/QC-20/QC-40/QC-50/QC-50 Remote/QC-100/Qc-100 Remote O U B Lteitslheo O T I N G

Page 30

T R O U B LTEITSLHEO O T I N G

CONTROL ERROR DISPLAYS

control display	action required

Real Time Clock Bad	This is likely caused by the unit having been unplugged for an extended
E-60: REAL TIME CLOCK DEFAULTS LOADED,	amount of time. The data stored in the Real-Time Clock has been reset to
VERIFY CORRECT TIME, POWER CYCLE UNIT TO	the factory default values. Contact service if problem persists.
CLEAR THIS MESSAGE.

Real Time Clock Not Detected	Real Time Clock not detected. Contact service if problem persists.
E-61: REAL TIME CLOCK NOT DETECTED.
POWER CYCLE UNIT AND CALL FOR
SERVICE IF THE PROBLEM PERSISTS.

Button Stuck	This error message indicates that a button is stuck. Check all buttons.
E-90: BUTTON STUCK. CHECK ALL BUTTONS AND	Error will clear when the problem has been solved. Contact service is
ERROR WILL CLEAR WHEN THE PROBLEM HAS	problem persists.
BEEN RESOLVED

Using Default Function Values	This error message indicates the control memory is not correctly reading
E-80 - EEPROM ERROR	user-set values. The Quickchiller will remain operational but the user
USING DEFAULT FUNCTION VALUES	defined settings will be reloaded to the default values. The control will
	revert to factory default settings and will require operator modification
	each time the unit is used. Call Service. Acknowledge error by pressing
	the power button.

Probe Open/Shorted	This error message indicates a problem with the probe identified within the
PROBE N* OPEN -OR- PROBE N* SHORTED	display. The Quickchiller will operate normally in the Time mode but will
CALL FOR SERVICE	not operate in the Probe mode. Call service.
	*N signifies probe number that is shorted: 1= top, 2= middle, 3= bottom

Cavity Open Shorted	This error message indicates a problem with the interior cavity sensor. The
CAVITY SENSOR OPEN OR SHORTED.	Quickchiller will not operate in any operational mode. Call service.
CALL FOR SERVICE

Coil Open Shorted	This error message indicates a problem with the display identified coil
COIL N* OPEN OR COIL N* SHORTED	sensor. The Quickchiller will remain operational but will extend the
CALL FOR SERVICE	defrost cycle to the full period of 20 minutes. Call service.
	*N signifies coil number that is shorted.

Bad Calibration	Calibration bad. Call service.
E-81: BAD CALIBRATION. PLEASE CALL SERVICE	Note: Display will signify PASS where calibration is good, or FAIL
AD1-0=(PASS) (FAIL) AD1-1=(PASS)(FAIL)
AD2-0=(PASS)(FAIL) AD2-1=(PASS)(FAIL)	where calibration is bad.
AD3-0=(PASS)(FAIL) AD3-1=(PASS)(FAIL)

Requires Calibration	Requires Calibration. Call service.
E-82: REQUIRES CALIBRATION.
PLEASE CALL SERVICE

Power Failure	Power has been off. Press Program to acknowledge.
POWER WAS OFF FOR HH:MM	NOTE: If such an event has occurred, it is strongly recommended
PRESS PROGRAM TO ACKNOWLEDGE	that you ensure the food is safe for consumption according to
	local health regulations.

QUICKCHILLER • INSTALLATION/OPERATION/SERVICE MANUAL • 2 8 .

Image 30

Contents Installation Wire Diagrams L I V E R Y P a C K I N GSafety Procedures Precautions N G E RSite Installation InstallationInstallation Unit must not be tipped on its side At any timeDoor Seal Installation RequirementsWater Drainage DrainageTrolley Guide Installation Trolley Guide InstallationSiteub Titleinstallation S Ttailtllaet I O NQC-3 1626mm x 1143mm x 1143mm S Ttailtllaet I onQC-20 R404a Refrigerant404a Refrigerant QC-4044 x 47 x 79 1118mm x 1194mm x 2007mm Approximately 144 lb 65 kg maximumQC-50 QC-50 Remote QC-100 QC-100 RemoteQC-3 QC-20 QC-40 QC-50 QC-100 Optionssub Titleand AccessoriesModel Casters, 5 127mm208-240VAC 50/60 Hz Electrical SpecificationsElectricalsub Title 380-415VAC 50/60 HzTraditional COOK-SERVE Kitchens Etritaltei O NOperating Introduction Modified COOK-CHILL OperationsChill Processing Cycles Quickchiller Operation ModesInitial Quickchiller Operation FAN Operation Power OutageAdditional Information DoorControl Panel Identification Basicsub Titleoperation Manual OperationWhen in the Hold Temp Mode After a Chill Mode Advancedsub Title OperationHold Temp Chilling by Time Factory Default SET PointsWhen in the Hold Temp Mode After Chilling by Probe Chilling by ProbePreset Selections Preset Program OperationProgramming Presets E R a T I O NUser Settings Operationt I T L EUser Information Time & Temperature GuidelinesFood Probe USE Automatic DefrostFoodsub Titlehandling Guidelines Product CoveringPortioning & Packaging Product Capacity PER PAN Quickchiller PAN CapacityI C K C H I L L E R P a N C a P a C I T Y C H a R T D I V I D U a L P a N C a P a C I T I E SStarches PAN Size ›Breakfast Items DessertsCleaning Agents Care Andti T CleaningeCleaning and Preventive Maintenance Cleaning MaterialsFood Trolley Cleaning Interior CleaningExterior Cleaning Monthly Compressor & Condenser MaintenanceO U B Lteitslheo O T I N G Etritvlice E Model QC-3 ControlEtritvlice E Model QC-3 CoilModel QC-20 Control Model QC-20 Coil Model QC-20 Condenser Model QC-40 Model QC-40 Control Model QC-50, QC-100 Control Model QC-100 Coil Model QC-50, QC-100 Breaker Model QC-50, QC-100 FANModel QC-50 Remote Model QC-50, QC-100 Remote Remote condensor connectionModel QC-3 Wiring Model QC-20 Wiring Model QC-40 Wiring Model QC-50 Wiring 1PH 3PH Model QC-100 Wiring 1PH 3PH Page Page Page Page Page Page Page Page Page Page Page Page Page Limited Warranty