Sherwood R-863 manual RPT Extra Surr Title

Page 22

ENGLISH

Continued

When playing some multi-channel program sources in the Extra Surround 6.1/7.1 mode.

RPT

A

EXTRA SURR.

TITLE

7.1 SURR

6.1/7.1

or

When the digital signals from the following program sources only are input in the available decoding mode, if these buttons are pressed, the corresponding surround mode will be selected.

Dolby Digital 5.1-channel sources(including THX Surround EX created using the Dolby Digital Surround EX technology) : EXTRA SURROUND mode,

DTS 5.1-channel sources : DTS ES MATRIX mode.

Press the EXTRA SURROUND 6.1/7.1 button on the front panel or the 7.1 CH SURROUND button on the remote control again to cancel the 6.1(or 7.1) surround mode.

According to whether the surround back speaker is set to “1CH” or “2CH”, the 6.1 or 7.1 mode is selected. However, when the surround back speaker is set to “None”, the Extra Surround 6.1/7.1 mode cannot be activated.

When canceling the surround mode for normal stereo operation.

STEREO

or

ST

Then the stereo mode is selected.

To cancel the stereo mode, select the desired surround mode with using the MULTI CONTROL knob or the DSP MODE button, etc.

22

Image 22

Contents 863 Unpacking and Installation IntroductionRead this Before Operating Your Unit Introduction Connecting Audio Components System ConnectionsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Front Panel Controls Dynamic Range ButtonDigi Link System Remote Controls Universal Remote ControlsThis remote control has 3 operating modes as follows Function Table of the Numbered Buttons Remove the cover Loading BatteriesMatching the polarity Additional Information on Remote Command Codes Functions CodesEntering a Setup Code VOLBefore operation OperationsListening to a Program Source Video 1 Video 2 Video 3 VideoSelect the tone mode as desired When CD, Tape MON or Video 1~ Video 4 is selectedAdjusting the tone bass and treble Select the digital or the analog input as DesiredProgram sources, if the headphones are plugged When listening to DTS, Dolby Digital or MpegEnsure that the Speaker button is set to off Surround Sound Surround modesTheater Speaker placement Front left and right speakers and center speakerEnjoying Surround Sound Necessary decoding process for optimum surround modesRPT Extra Surr Title Adjusting each channel level with test Adjusting each channel levelTone Downmixing into 2 front channels Presetting radio stations Auto tuningManual tuning Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceRecording with Tape Monitor Dubbing the sound and image signalsRecording Dubbing from video components ontoConnected, Digital is flickering. There Digital Audio Recording with MD RecorderInput is selected as follows Will be no recording as well as no soundOther Functions Operating the sleep timerAdjusting the brightness of the fluorescent displays Compressing the dynamic range Dolby Digital sources onlyEntering a video label Correcting or clearing a video labelRoom 2 Source Playback OSD Menu Settings Using the OSDCurrent Status Display When selecting the Speaker Setup Select the desired menu using the Cursor UP , Down buttonsWhen selecting the CH Level Trim When selecting the Surround SetupWhen selecting the Speaker Config Setting the Speaker SetupPress the Cursor UP When selecting the Speaker Distance Enter buttonWhen selecting the LFE Level Control Buttons to select the desired LFE level modeWhen selecting the Input Setup Setting the Function SelectPress the Cursor UP /DOWN Press the Cursor Left Treble cannot be adjusted When selecting the Tone ControlOff Select this when adjusting tone for your taste Changes as followsOn To turn on the current status display When selecting the OSD ModeOff To turn off the current status display When selecting the Source Direct Setting the Surround SetupWhen selecting the Cinema EQ When selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeRoom 2 Feed mode to Off to save electricity When selecting the Function Select for RoomRoom 2 source cannot be selected Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section863