Sherwood R-863 manual Connecting Video Components

Page 6

ENGLISH

CONNECTING VIDEO COMPONENTS

COMPONENT VIDEO OUT

Video deck or additonal video component

S-VIDEO IN

VIDEO IN

S-VIDEO OUT

VIDEO OUT

AUDIO

PLAY(OUT)

AUDIO

REC(IN)

Green

Blue

Red

Green

Blue

Red

Green

Blue

Red

VIDEO IN

S-VIDEO IN

Monitor TV

COMPONENT VIDEO IN

DVD player

COMPONENT

VIDEO OUT

LD player or additonal video component

S-VIDEO OUT

VIDEO OUT

AUDIO OUT

S-VIDEO OUT

VIDEO OUT

AUDIO OUT

The VIDEO 1 jacks may also be connected to a DVD recorder or other digital video recording component. For details, refer to the operating instructions of the component to be connected.

There are three kinds of video jacks (COMPONENT, S, normal (composite)) for connecting video components. Connect them to the corresponding VIDEO jacks (VIDEO 1~3) respectively according to their capability.

The VIDEO 2(or VIDEO 3) jacks may also be connected to an additional video component such as a video deck, a cable TV tuner, an LD player or satellite system, etc.

This unit incorporates COMPONENT as well as S and normal(composite) VIDEO jacks.

For your reference, the excellence in picture quality is as follows: "COMPONENT" > "S"> normal(composite) "VIDEO".

When making COMPONENT VIDEO connections, connect "Y" to "Y", "CB" to "CB" (or "B-Y", "PB") and "CR" to "CR"(or "R- Y", "PR").

Signals input into the COMPONENT VIDEO IN jacks will be output in only the MONITOR COMPONENT VIDEO OUT jacks.

A signal input into the normal(composite) VIDEO IN jack will be output in the normal(composite) VIDEO OUT jacks and a signal

input into the S-VIDEO IN jack will be output in the S-VIDEO OUT jacks. Notes :

Neither on-screen display function nor video recording are available when using the COMPONENT VIDEO connections.

When Sherwood DVD player such as V-756, etc. is connected to the DIGI LINK jack for system control, you should connect the DVD player to the "VIDEO 2" jacks of this unit. Because, if the PLAY button, etc. is pressed on the DVD player, the VIDEO 2 is automatically selected as an input source on this unit. Then the playback, etc. starts.

6

Image 6
Contents 863 Unpacking and Installation IntroductionRead this Before Operating Your Unit Introduction Connecting Audio Components System ConnectionsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Front Panel Controls Dynamic Range ButtonUniversal Remote Controls Digi Link System Remote ControlsThis remote control has 3 operating modes as follows Function Table of the Numbered Buttons Loading Batteries Remove the coverMatching the polarity Additional Information on Remote Command Codes Functions CodesEntering a Setup Code VOLBefore operation OperationsListening to a Program Source Video 1 Video 2 Video 3 VideoSelect the tone mode as desired When CD, Tape MON or Video 1~ Video 4 is selectedAdjusting the tone bass and treble Select the digital or the analog input as DesiredWhen listening to DTS, Dolby Digital or Mpeg Program sources, if the headphones are pluggedEnsure that the Speaker button is set to off Surround Sound Surround modesTheater Speaker placement Front left and right speakers and center speakerEnjoying Surround Sound Necessary decoding process for optimum surround modesRPT Extra Surr Title Adjusting each channel level Adjusting each channel level with testTone Downmixing into 2 front channels Presetting radio stations Auto tuningManual tuning Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceRecording with Tape Monitor Dubbing the sound and image signalsRecording Dubbing from video components ontoConnected, Digital is flickering. There Digital Audio Recording with MD RecorderInput is selected as follows Will be no recording as well as no soundOther Functions Operating the sleep timerAdjusting the brightness of the fluorescent displays Compressing the dynamic range Dolby Digital sources onlyEntering a video label Correcting or clearing a video labelRoom 2 Source Playback Using the OSD OSD Menu SettingsCurrent Status Display When selecting the Speaker Setup Select the desired menu using the Cursor UP , Down buttonsWhen selecting the CH Level Trim When selecting the Surround SetupSetting the Speaker Setup When selecting the Speaker ConfigPress the Cursor UP When selecting the Speaker Distance Enter buttonWhen selecting the LFE Level Control Buttons to select the desired LFE level modeSetting the Function Select When selecting the Input SetupPress the Cursor UP /DOWN Press the Cursor Left Treble cannot be adjusted When selecting the Tone ControlOff Select this when adjusting tone for your taste Changes as followsWhen selecting the OSD Mode On To turn on the current status displayOff To turn off the current status display Setting the Surround Setup When selecting the Source DirectWhen selecting the Cinema EQ When selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Function Select for Room Room 2 Feed mode to Off to save electricityRoom 2 source cannot be selected Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section863