Sherwood R-863 manual Recording with Tape Monitor, Dubbing from video components onto

Page 27

RECORDING

The analog signals from the 7.1 CH DIRECT inputs as well as the digital signals from the coaxial or optical digital input can be heard but cannot be recorded.

The volume, tone (bass, treble) settings,etc. have no effect on the recording signals.

Recording with TAPE MONITOR

2

Start recording on the component hooked

up to TAPE MONITOR.

1

Select the desired input as recording source

except TAPE MONITOR.

 

 

AUDIO

VIDEO

 

 

3

Start play on the desired input.

 

or TUNER

CD

AUX

 

 

VID1

VID2

VID3 VID4

 

 

Be sure that “TAPE MON” goes off.

For tape monitor function, refer to “TAPE MONITOR

function” on page 15.

Dubbing from video components onto

2

Start recording on the component hooked

up to VIDEO 1.

VIDEO 1

 

 

 

 

 

 

 

 

 

1

Select VIDEO 2, VIDEO 3 or VIDEO 4

 

 

as a recording source.

3

Start play on the component hooked up

 

 

 

 

 

 

VIDEO

 

 

to VIDEO 2, VIDEO 3 or VIDEO 4.

 

or

 

 

The audio and video signals from the VIDEO 2,

 

 

 

 

 

 

 

 

VIDEO 3 or VIDEO 4 component will be dubbed

 

VID2

VID3

VID4

onto the VIDEO 1 and you can enjoy them on the TV

 

 

 

 

set and from the speakers.

Dubbing the sound and image signals

2

Select CD as the sound recording source.

 

separately onto VIDEO 1

 

 

 

Example) When dubbing the VIDEO 2 image signal

 

 

and the CD sound signal separately onto

 

AUDIO

VIDEO 1.

 

 

 

or

 

Select VIDEO 2 as a image recording

 

1

 

 

source.

 

 

 

CD

 

VIDEO

 

 

 

 

 

or

 

 

 

 

 

 

VID2

 

 

 

 

 

 

 

Image source Sound source

Image source Sound source

27

ENGLISH

Page 26 Page 28
Image 27
Page 26 Page 28
Contents 863 Introduction Unpacking and InstallationRead this Before Operating Your Unit Introduction System Connections Connecting Audio ComponentsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Dynamic Range Button Front Panel ControlsUniversal Remote Controls Digi Link System Remote ControlsThis remote control has 3 operating modes as follows Function Table of the Numbered Buttons Loading Batteries Remove the coverMatching the polarity Functions Codes Additional Information on Remote Command CodesVOL Entering a Setup CodeVideo 1 Video 2 Video 3 Video OperationsListening to a Program Source Before operationSelect the digital or the analog input as Desired When CD, Tape MON or Video 1~ Video 4 is selectedAdjusting the tone bass and treble Select the tone mode as desiredWhen listening to DTS, Dolby Digital or Mpeg Program sources, if the headphones are pluggedEnsure that the Speaker button is set to off Surround modes Surround SoundTheater Front left and right speakers and center speaker Speaker placementNecessary decoding process for optimum surround modes Enjoying Surround SoundRPT Extra Surr Title Adjusting each channel level Adjusting each channel level with testTone Downmixing into 2 front channels Listening to Radio Broadcasts Auto tuningManual tuning Presetting radio stationsScanning preset stations in sequence Tuning to preset stationsDubbing from video components onto Dubbing the sound and image signalsRecording Recording with Tape MonitorWill be no recording as well as no sound Digital Audio Recording with MD RecorderInput is selected as follows Connected, Digital is flickering. ThereCompressing the dynamic range Dolby Digital sources only Operating the sleep timerAdjusting the brightness of the fluorescent displays Other FunctionsCorrecting or clearing a video label Entering a video labelRoom 2 Source Playback Using the OSD OSD Menu SettingsCurrent Status Display When selecting the Surround Setup Select the desired menu using the Cursor UP , Down buttonsWhen selecting the CH Level Trim When selecting the Speaker SetupSetting the Speaker Setup When selecting the Speaker ConfigPress the Cursor UP Enter button When selecting the Speaker DistanceButtons to select the desired LFE level mode When selecting the LFE Level ControlSetting the Function Select When selecting the Input SetupPress the Cursor UP /DOWN Press the Cursor Left Changes as follows When selecting the Tone ControlOff Select this when adjusting tone for your taste Treble cannot be adjustedWhen selecting the OSD Mode On To turn on the current status displayOff To turn off the current status display Setting the Surround Setup When selecting the Source DirectWhen selecting the Cinema EQ When selecting the surround mode When selecting the Decoding ModeSetting the CH Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen selecting the Function Select for Room Room 2 Feed mode to Off to save electricityRoom 2 source cannot be selected Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications863
Top Page Image Contents