Sherwood R-863 manual Setting the ROOM2 Feed Setup, When selecting the Volume Mode

Page 44

ENGLISH

SETTING THE ROOM2 FEED SETUP

R O O M 2 F E E D S E T U P

V O L U M E M O D E

 

 

 

 

 

To select the desired volume mode.

 

 

 

 

 

F U N C T I O N S E L E C T

 

 

 

 

To select the desired ROOM 2 source.

R E T U R N : B a c k

E N T E R : S e l e c t

 

 

 

 

 

 

 

The ROOM 2 function allows you to enjoy one source in the main room while playing another in a different room at the same time.

The analog signals from the 7.1 CH DIRECT inputs and TAPE MONITOR INs as well as the digital signals from the coaxial or optical digital input cannot be output from the ROOM2 OUTs.

When selecting the VOLUME MODE

1

Press the CURSOR UP( )/DOWN( ) buttons to select the VOLUME MODE, then press the ENTER

button.

 

 

 

 

 

 

V O L U M E M O D E

 

VOL. CH LEVEL

 

 

 

 

 

ENTER

V O L U M E M O D E :

Variable

 

 

 

R E T U R N : B a c k

, : S e l e c t

 

HOME THEATER MASTER

 

 

 

 

RNC-220

 

 

 

2

Press the CURSOR LEFT(

)/RIGHT( ) buttons to select the desired volume mode for the ROOM 2

source.

 

Each time these buttons are pressed, the volume mode

 

 

 

 

 

 

changes as follows:

 

 

VOL. CH LEVEL

 

Variable : Select this when an power amplifier is connected

 

to the ROOM 2(audio) OUTs for ROOM 2 source

 

playback. You can adjust the ROOM 2 volume

 

level with the MASTER VOLUME CONTROL

 

knob of this receiver or the VOLUME

HOME THEATER MASTER

UP/DOWN buttons on the remote control.

RNC-220

 

 

Fixed : Select this when an integrated amplifier, etc. is

 

connected to the ROOM 2(audio) OUTs. You can

 

adjust the ROOM 2 volume level on the connected

 

integrated amplifier, etc.

Notes :

When selecting the Fixed mode, first adjust the volume level as desired in the Variable mode and select the Fixed mode. Then the volume level will be fixed to the adjusted level.

In case that an integrated amplifier, etc. is connected to the ROOM 2(audio) OUTs and the volume mode is set to Variable, if the ROOM 2 volume level is adjusted to high level on both this receiver and the connected amplifier, the ROOM 2 speaker and the connected amplifier may be damaged.

Therefore, be sure to set the volume mode to Fixed for safe operation when using amplifier or receiver with its own volume control for ROOM 2.

44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents 863 Unpacking and Installation IntroductionRead this Before Operating Your Unit Introduction Connecting Audio Components System ConnectionsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Front Panel Controls Dynamic Range ButtonThis remote control has 3 operating modes as follows Universal Remote ControlsDigi Link System Remote Controls Function Table of the Numbered Buttons Matching the polarity Loading BatteriesRemove the cover Additional Information on Remote Command Codes Functions CodesEntering a Setup Code VOLOperations Listening to a Program SourceBefore operation Video 1 Video 2 Video 3 VideoWhen CD, Tape MON or Video 1~ Video 4 is selected Adjusting the tone bass and trebleSelect the tone mode as desired Select the digital or the analog input as DesiredEnsure that the Speaker button is set to off When listening to DTS, Dolby Digital or MpegProgram sources, if the headphones are plugged Surround Sound Surround modesTheater Speaker placement Front left and right speakers and center speakerEnjoying Surround Sound Necessary decoding process for optimum surround modesRPT Extra Surr Title Tone Adjusting each channel levelAdjusting each channel level with test Downmixing into 2 front channels Auto tuning Manual tuningPresetting radio stations Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceDubbing the sound and image signals RecordingRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Input is selected as followsConnected, Digital is flickering. There Will be no recording as well as no soundOperating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Compressing the dynamic range Dolby Digital sources onlyEntering a video label Correcting or clearing a video labelRoom 2 Source Playback Current Status Display Using the OSDOSD Menu Settings Select the desired menu using the Cursor UP , Down buttons When selecting the CH Level TrimWhen selecting the Speaker Setup When selecting the Surround SetupPress the Cursor UP Setting the Speaker SetupWhen selecting the Speaker Config When selecting the Speaker Distance Enter buttonWhen selecting the LFE Level Control Buttons to select the desired LFE level modePress the Cursor UP /DOWN Setting the Function SelectWhen selecting the Input Setup Press the Cursor Left When selecting the Tone Control Off Select this when adjusting tone for your tasteTreble cannot be adjusted Changes as followsOff To turn off the current status display When selecting the OSD ModeOn To turn on the current status display When selecting the Cinema EQ Setting the Surround SetupWhen selecting the Source Direct When selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeRoom 2 source cannot be selected When selecting the Function Select for RoomRoom 2 Feed mode to Off to save electricity Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section863
Top Page Image Contents