Sherwood R-863 manual Room 2 Source Playback

Page 31

ROOM 2 SOURCE PLAYBACK

This function allows enjoying one source in the main room and playing another in a different room at the same time.

The analog signals from the 7.1 CH DIRECT inputs and TAPE MONITOR INs as well as the digital signals from the coaxial or optical digital input cannot be output from the ROOM 2 OUTs, meaning no playback in a different room.

When you connect the multi - room adapter to the MULTI - ROOM jack of this unit, you can control this unit with its remote control unit in a different room, too. (For details, refer to “CONNECTING MULTI - ROOM SYSTEM KIT” on page 8.)

ENGLISH

Press the ROOM 2 button.

1

ROOM2 FEED

or

ROOM2

“R2” will flicker for 3 seconds and the ROOM 2 function is activated.

To cancel the ROOM 2 function, press it again. Then “R2” goes off

You can cancel the ROOM 2 function with using these buttons even in the standby mode.

2	Select the desired input as a ROOM 2
	source while “R2” is flickering.

AUDIO VIDEO

or

TUNER

CD

AUX

VID1 VID2 VID3 VID4

The selected ROOM 2 source is displayed for 3 seconds as follows : (R2) TUNER, (R2) CD, (R2) AUX, (R2) VIDEO 1~4.

Only these sources can be played in another room. When an audio program source is selected, as a ROOM 2 source, the image of the video program source selected previously can be played separately, too.

(For details, refer to “SETTING THE ROOM 2 FEED SETUP”on page 44.)

Only while “R2” is flickering, the volume level for the ROOM 2 source can be adjusted.

When “R2” is not flickering and lights up, press the ROOM 2 button again briefly twice.

Start play on the component related to the
3 ROOM 2 source.	Notes:
	Even when this unit enters the standby mode, in
	such a case that “R2” lights up still and the
	STANDBY button lights up in blue as it does in the
	operating mode, meaning only the ROOM 2 circuitry
	operates, the ROOM 2 source selected previously
	can be played independently.
	When you do not use the ROOM 2 function, cancel
	the ROOM 2 function to save electricity.
	For ROOM 2 volume adjustment, refer to “SETTING
	THE ROOM 2 FEED SETUP” on page 44.

31

Image 31

Contents 863 Introduction Unpacking and InstallationRead this Before Operating Your Unit Introduction System Connections Connecting Audio ComponentsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Dynamic Range Button Front Panel ControlsDigi Link System Remote Controls Universal Remote ControlsThis remote control has 3 operating modes as follows Function Table of the Numbered Buttons Remove the cover Loading BatteriesMatching the polarity Functions Codes Additional Information on Remote Command CodesVOL Entering a Setup CodeVideo 1 Video 2 Video 3 Video OperationsListening to a Program Source Before operationSelect the digital or the analog input as Desired When CD, Tape MON or Video 1~ Video 4 is selectedAdjusting the tone bass and treble Select the tone mode as desiredProgram sources, if the headphones are plugged When listening to DTS, Dolby Digital or MpegEnsure that the Speaker button is set to off Surround modes Surround SoundTheater Front left and right speakers and center speaker Speaker placementNecessary decoding process for optimum surround modes Enjoying Surround SoundRPT Extra Surr Title Adjusting each channel level with test Adjusting each channel levelTone Downmixing into 2 front channels Listening to Radio Broadcasts Auto tuningManual tuning Presetting radio stationsScanning preset stations in sequence Tuning to preset stationsDubbing from video components onto Dubbing the sound and image signalsRecording Recording with Tape MonitorWill be no recording as well as no sound Digital Audio Recording with MD RecorderInput is selected as follows Connected, Digital is flickering. ThereCompressing the dynamic range Dolby Digital sources only Operating the sleep timerAdjusting the brightness of the fluorescent displays Other FunctionsCorrecting or clearing a video label Entering a video labelRoom 2 Source Playback OSD Menu Settings Using the OSDCurrent Status Display When selecting the Surround Setup Select the desired menu using the Cursor UP , Down buttonsWhen selecting the CH Level Trim When selecting the Speaker SetupWhen selecting the Speaker Config Setting the Speaker SetupPress the Cursor UP Enter button When selecting the Speaker DistanceButtons to select the desired LFE level mode When selecting the LFE Level ControlWhen selecting the Input Setup Setting the Function SelectPress the Cursor UP /DOWN Press the Cursor Left Changes as follows When selecting the Tone ControlOff Select this when adjusting tone for your taste Treble cannot be adjustedOn To turn on the current status display When selecting the OSD ModeOff To turn off the current status display When selecting the Source Direct Setting the Surround SetupWhen selecting the Cinema EQ When selecting the surround mode When selecting the Decoding ModeSetting the CH Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupRoom 2 Feed mode to Off to save electricity When selecting the Function Select for RoomRoom 2 source cannot be selected Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications863