Sherwood R-863 manual Universal Remote Controls, Digi Link System Remote Controls

Page 10

ENGLISH

Universal Remote Controls

Note: For enhanced Universal Remote Programming instructions and manufacturer’s codes, please refer to the operating manual inclosed with this Universal Remote Control.

This remote control has 3 operating modes as follows:

OSD (On-Screen Display) mode: Allows you to look at information about basic operation of this unit on your monitor TV and to operate this unit by moving an arrow that appears on the screen of your monitor TV.

Sherwood mode: Allows you to operate this unit and other Sherwood components like cassette decks, CD players, etc.(To operate other Sherwood components, you should make the DIGI LINK connections between them.)

Non-Sherwood mode: Allows you to operate other non-Sherwood audio and video components that are remote compatible.

Notes:

The setup code for each component must be entered before operation.

For setup codes(manufacturer’s codes), please refer to “Set-Up Code Tables” in the operating manual of this remote control.

Some operation buttons have different functions according to each operation mode.

Be sure to set the remote control to the correct mode before operation.

DIGI LINK SYSTEM REMOTE CONTROLS

This section explains the basic functions for Sherwood or OSD mode. For the non-Sherwood mode, refer to the operating manual of this remote control.

All Sherwood components bearing the DIGI LINK (II or III) logo can be used with this remote control.

For system remote control operation, first make the DIGI LINK connections between Sherwood components.

The numbered buttons on the remote control have different functions in different modes. For details, refer to the “FUNCTION TABLE of the NUMBERED BUTTONS” on the following page.

In the DIGI LINK III remote control system, if pressing PLAY, etc. on CD player or tape deck, CD or TAPE MONITOR is selected automatically on the receiver without selecting the input source. Then PLAY, etc. starts.

LED LAMP

DEVICE BUTTONS

To operate the desired component with this remote control, first select the corresponding DEVICE button.

DVD

POWER BUTTON

ENTER BUTTON

NUMERIC(1~0) BUTTONS

For selecting preset stations in tuner mode.

For selecting a track or a disc in CD mode, etc.

When selecting a disc, select disc No. (1~5) within 2 sec. after pressing DISC(marked "P.SCAN") button.

 

 

VOLUME UP/DOWN( / ) BUTTONS

VOL.

CH LEVEL

CHANNEL LEVEL UP/DOWN( / ) BUTTONS

OSD

CH SEL

ENTER

CURSOR CONTROL(

,

,

,

) BUTTONS

RPT

INTRO

 

 

 

 

A

B

 

 

 

 

TITLE

 

 

7.1 SURR

 

RETURN

 

 

AUTO

 

 

DSP

 

 

MODE

 

 

ST

DISC

TEST

CENTER

P.SCAN

TONE

MODE

TUNER CD T1/MON AUX PHONO

VID1 VID2 VID3 VID4 VID5

SYS DISP SLEEP DIRECT IN ROOM2

LIGHT BUTTON

Activates the backlighting of the remote control

HOME THEATER MASTER

RNC-220

for 7 sec. If any other button is pressed while

 

the backlighting is on, the remote control will

 

remain backlit for an additional 7 sec.

 

10

Image 10
Contents 863 Unpacking and Installation IntroductionRead this Before Operating Your Unit Introduction Connecting Audio Components System ConnectionsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Front Panel Controls Dynamic Range ButtonDigi Link System Remote Controls Universal Remote ControlsThis remote control has 3 operating modes as follows Function Table of the Numbered Buttons Remove the cover Loading BatteriesMatching the polarity Additional Information on Remote Command Codes Functions CodesEntering a Setup Code VOLBefore operation OperationsListening to a Program Source Video 1 Video 2 Video 3 VideoSelect the tone mode as desired When CD, Tape MON or Video 1~ Video 4 is selectedAdjusting the tone bass and treble Select the digital or the analog input as DesiredProgram sources, if the headphones are plugged When listening to DTS, Dolby Digital or MpegEnsure that the Speaker button is set to off Surround Sound Surround modesTheater Speaker placement Front left and right speakers and center speakerEnjoying Surround Sound Necessary decoding process for optimum surround modesRPT Extra Surr Title Adjusting each channel level with test Adjusting each channel levelTone Downmixing into 2 front channels Presetting radio stations Auto tuningManual tuning Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceRecording with Tape Monitor Dubbing the sound and image signalsRecording Dubbing from video components ontoConnected, Digital is flickering. There Digital Audio Recording with MD RecorderInput is selected as follows Will be no recording as well as no soundOther Functions Operating the sleep timerAdjusting the brightness of the fluorescent displays Compressing the dynamic range Dolby Digital sources onlyEntering a video label Correcting or clearing a video labelRoom 2 Source Playback OSD Menu Settings Using the OSDCurrent Status Display When selecting the Speaker Setup Select the desired menu using the Cursor UP , Down buttonsWhen selecting the CH Level Trim When selecting the Surround SetupWhen selecting the Speaker Config Setting the Speaker SetupPress the Cursor UP When selecting the Speaker Distance Enter buttonWhen selecting the LFE Level Control Buttons to select the desired LFE level modeWhen selecting the Input Setup Setting the Function SelectPress the Cursor UP /DOWN Press the Cursor Left Treble cannot be adjusted When selecting the Tone ControlOff Select this when adjusting tone for your taste Changes as followsOn To turn on the current status display When selecting the OSD ModeOff To turn off the current status display When selecting the Source Direct Setting the Surround SetupWhen selecting the Cinema EQ When selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeRoom 2 Feed mode to Off to save electricity When selecting the Function Select for RoomRoom 2 source cannot be selected Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section863