Sherwood R-863 manual Operations, Listening to a Program Source, Before operation

Page 15

Operations

Notes :

Before operating this receiver with the supplied remote control, refer to “Universal Remote Controls” on page 10 for details about operation. Before operating this receiver, first set this unit as desired for optimum performance, by using the OSD menu setting procedures. (For details, refer to “OSD Menu Settings” on page 32.)

LISTENING TO A PROGRAM SOURCE

ENGLISH

Before operation

Enter the standby mode.

POWER

 

ON / OFF

The STANDBY button lights up in red.

This means that the receiver is not disconnected from the AC mains and a small amount of current is retained to support the memorized contents and operation readiness.

To switch the power off, push the POWER switch again.

Then power is cut off and the STANDBY button goes off.

In the standby mode, turn the power on.

1

STANDBY

ON/STANDBY

or

Each time the STANDBY button on the front panel or the POWER button on the remote control is pressed, the receiver is turned on to enter the operating mode(the STANDBY button lights up in blue) or off to enter the standby mode (the STANDBY button lights up in red).

In the standby mode, if one of the INPUT SELECTOR buttons is pressed, the receiver is turned on automatically and the desired input is selected.

Switch the speakers on.

SPEAKER

 

2

ON/OFF

Then the SPEAKER indicator lights up on the display and sound can be heard from the speakers connected to the speaker terminals.

When using headphones for private listening, press the SPEAKER button again to switch the speakers off.

Select the desired input source.

3

INPUT SELECTOR

AUDIO VIDEO TAPE MON.

TUNER CD T1/MON AUX

or

VID1 VID2 VID3 VID4

Each time the “AUDIO” button is pressed, the input source changes as follows:

TUNER CD AUX (frequency display)

Each time the “VIDEO” button is pressed, the input source changes as follows:

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4

When the TAPE MONITOR button is set to on so that “TAPE MON” lights up, other inputs can not be heard from the speakers.

To listen to an input source except TAPE MONITOR, be sure to set the TAPE MONITOR button to off.

TAPE MONITOR function

You can connect either a tape deck or a graphic equalizer to the receiver’s TAPE MONITOR jacks.

Only when you listen to the component connected to these jacks, set the TAPE MONITOR button to on.

If you connect a 3-head tape deck, you can listen to the sound being recorded during recording, and not the source sound. For further details, refer to the operating instructions of the connected component.

When selecting the 7.1 CH DIRECT as desired

7.1CH DIRECT

or

DIRECT IN

Depending on the surround back speaker setting, “7.1(,6.1 or 5.1) CH DIRECT” is displayed and the 8(/7/6) separate analog signals from the component connected to this input pass through the tone, volume and bass management(if selected) circuits only and can be heard from your speakers.(In case that the TAPE MONITOR button is set to on, the TAPE MONITOR button is automatically set to off.)

Press the 7.1 CH DIRECT button or select the desired input source to cancel the 7.1 CH direct function.

These analog signals can be heard only. They cannot be recorded.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 863 Introduction Unpacking and InstallationRead this Before Operating Your Unit Introduction System Connections Connecting Audio ComponentsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Dynamic Range Button Front Panel ControlsUniversal Remote Controls Digi Link System Remote ControlsThis remote control has 3 operating modes as follows Function Table of the Numbered Buttons Loading Batteries Remove the coverMatching the polarity Functions Codes Additional Information on Remote Command CodesVOL Entering a Setup CodeVideo 1 Video 2 Video 3 Video OperationsListening to a Program Source Before operationSelect the digital or the analog input as Desired When CD, Tape MON or Video 1~ Video 4 is selectedAdjusting the tone bass and treble Select the tone mode as desiredWhen listening to DTS, Dolby Digital or Mpeg Program sources, if the headphones are pluggedEnsure that the Speaker button is set to off Surround modes Surround SoundTheater Front left and right speakers and center speaker Speaker placementNecessary decoding process for optimum surround modes Enjoying Surround SoundRPT Extra Surr Title Adjusting each channel level Adjusting each channel level with testTone Downmixing into 2 front channels Listening to Radio Broadcasts Auto tuningManual tuning Presetting radio stationsScanning preset stations in sequence Tuning to preset stationsDubbing from video components onto Dubbing the sound and image signalsRecording Recording with Tape MonitorWill be no recording as well as no sound Digital Audio Recording with MD RecorderInput is selected as follows Connected, Digital is flickering. ThereCompressing the dynamic range Dolby Digital sources only Operating the sleep timerAdjusting the brightness of the fluorescent displays Other FunctionsCorrecting or clearing a video label Entering a video labelRoom 2 Source Playback Using the OSD OSD Menu SettingsCurrent Status Display When selecting the Surround Setup Select the desired menu using the Cursor UP , Down buttonsWhen selecting the CH Level Trim When selecting the Speaker SetupSetting the Speaker Setup When selecting the Speaker ConfigPress the Cursor UP Enter button When selecting the Speaker DistanceButtons to select the desired LFE level mode When selecting the LFE Level ControlSetting the Function Select When selecting the Input SetupPress the Cursor UP /DOWN Press the Cursor Left Changes as follows When selecting the Tone ControlOff Select this when adjusting tone for your taste Treble cannot be adjustedWhen selecting the OSD Mode On To turn on the current status displayOff To turn off the current status display Setting the Surround Setup When selecting the Source DirectWhen selecting the Cinema EQ When selecting the surround mode When selecting the Decoding ModeSetting the CH Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen selecting the Function Select for Room Room 2 Feed mode to Off to save electricityRoom 2 source cannot be selected Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications863
Top Page Image Contents