Sherwood R-863 manual When selecting the Tone Control, Changes as follows, Tone effect

Page 39

When selecting the TONE CONTROL

Press the CURSOR UP(

)/DOWN( ) buttons to select the TONE CONTROL, then press the ENTER

1 button.

 

 

 

 

T O N E C O N T R O L

 

VOL. CH LEVEL

T O N E D E F E A T

:

Off

 

ENTER

 

 

 

B A S S ----- + -----

0 dB

 

T R E B L E ----- + -----

0 dB

HOME THEATER MASTER

R E T U R N : B a c k

,

: S e l e c t

RNC-220

 

 

 

Note:

When the source direct function is activated, the TONE CONTROL cannot be selected.

Press the CURSOR LEFT(

)/RIGHT( ) buttons to select the desired tone defeat mode.

2

 

 

Each time these buttons are pressed, the tone defeat mode

 

changes as follows:

 

On : Select this when listening to a program source without

VOL. CH LEVEL

 

 

the tone effect.

 

Off : Select this when adjusting tone for your taste .

 

Note:

RNC-220

When the tone defeat mode is set to On, the tone (bass and

HOME THEATER MASTER

 

 

treble) cannot be adjusted.

When the tone defeat mode is set to Off to adjust the tone (bass and treble)

1. Press the CURSOR UP( )/DOWN(

) buttons to select the desired tone mode.

Each time these buttons are pressed, “

” is moved to the tone defeat mode or the corresponding tone mode.

2. At the desired tone mode, press the CURSOR LEFT( )/RIGHT( ) buttons to adjust the selected tone as desired. The tone level can be adjusted within the range of -10~+10 dB.

In general, we recommend the bass and treble to be adjusted to 0 dB(flat level). Extreme settings at high volume may damage your speakers.

3. To complete tone adjustment, repeat the above steps 1 and 2.

ENGLISH

39

Image 39
Contents 863 Introduction Unpacking and InstallationRead this Before Operating Your Unit Introduction System Connections Connecting Audio ComponentsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Dynamic Range Button Front Panel ControlsUniversal Remote Controls Digi Link System Remote ControlsThis remote control has 3 operating modes as follows Function Table of the Numbered Buttons Loading Batteries Remove the coverMatching the polarity Functions Codes Additional Information on Remote Command CodesVOL Entering a Setup CodeVideo 1 Video 2 Video 3 Video OperationsListening to a Program Source Before operationSelect the digital or the analog input as Desired When CD, Tape MON or Video 1~ Video 4 is selectedAdjusting the tone bass and treble Select the tone mode as desiredWhen listening to DTS, Dolby Digital or Mpeg Program sources, if the headphones are pluggedEnsure that the Speaker button is set to off Surround modes Surround SoundTheater Front left and right speakers and center speaker Speaker placementNecessary decoding process for optimum surround modes Enjoying Surround SoundRPT Extra Surr Title Adjusting each channel level Adjusting each channel level with testTone Downmixing into 2 front channels Listening to Radio Broadcasts Auto tuningManual tuning Presetting radio stationsScanning preset stations in sequence Tuning to preset stationsDubbing from video components onto Dubbing the sound and image signalsRecording Recording with Tape MonitorWill be no recording as well as no sound Digital Audio Recording with MD RecorderInput is selected as follows Connected, Digital is flickering. ThereCompressing the dynamic range Dolby Digital sources only Operating the sleep timerAdjusting the brightness of the fluorescent displays Other FunctionsCorrecting or clearing a video label Entering a video labelRoom 2 Source Playback Using the OSD OSD Menu SettingsCurrent Status Display When selecting the Surround Setup Select the desired menu using the Cursor UP , Down buttonsWhen selecting the CH Level Trim When selecting the Speaker SetupSetting the Speaker Setup When selecting the Speaker ConfigPress the Cursor UP Enter button When selecting the Speaker DistanceButtons to select the desired LFE level mode When selecting the LFE Level ControlSetting the Function Select When selecting the Input SetupPress the Cursor UP /DOWN Press the Cursor Left Changes as follows When selecting the Tone ControlOff Select this when adjusting tone for your taste Treble cannot be adjustedWhen selecting the OSD Mode On To turn on the current status displayOff To turn off the current status display Setting the Surround Setup When selecting the Source DirectWhen selecting the Cinema EQ When selecting the surround mode When selecting the Decoding ModeSetting the CH Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen selecting the Function Select for Room Room 2 Feed mode to Off to save electricityRoom 2 source cannot be selected Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications863