Sherwood R-863 manual Entering a video label, Correcting or clearing a video label

Page 30

ENGLISH

Entering a video label

2

Press the VIDEO LABEL button to enter the

video label mode.

 

 

This function can be operated only on video input

Example) When selecting VIDEO 1.

sources such as VIDEO 1~4.

 

 

1

Select the desired video input source to

 

VIDEO LABEL

enter its label.

 

 

 

VIDEO

 

 

 

or

 

 

 

VID1 VID2 VID3 VID4

 

 

3

Select the character on the flickering digit.

4

Confirm your selection.

MULTI CONTROL

VIDEO LABEL

 

 

 

 

 

 

 

 

Then the next digit will flicker.

Each time the MULTI CONTROL knob is rotated,

 

 

 

 

the characters change as follows:

 

 

 

 

 

5

Repeat the above steps and to enter

 

 

 

Blank (

)

the desired characters on the rest of the

Alphabets : A~Z, a~z

digits.

 

 

Numerals : 0~9

On up to 9 digits, the desired characters can be entered.

Note: If any button such as “AUDIO”, “VIDEO”, “7.1

 

 

 

 

 

 

 

CH DIRECT” button, etc. is pressed while

Symbols :

 

 

entering a video label, the video label mode will

 

 

 

 

be canceled.

MEMO/ENTER

Memorize the desired video label.

6

Correcting or clearing a video label

Select the desired video input source to be

1

rectified or cleared.

VIDEO

or

VID1 VID2 VID3 VID4

2

Repeat the steps ~ in “Entering a

video label” procedure.

To clear a video label, make a blank on each digit and memorize it, then the video label is cleared and its factory video input source will be displayed.

If the VIDEO LABEL button is pressed for more than 3 seconds, blanks will be made on all the digits at once.

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents 863 Unpacking and Installation IntroductionRead this Before Operating Your Unit Introduction Connecting Audio Components System ConnectionsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Front Panel Controls Dynamic Range ButtonUniversal Remote Controls Digi Link System Remote ControlsThis remote control has 3 operating modes as follows Function Table of the Numbered Buttons Loading Batteries Remove the coverMatching the polarity Additional Information on Remote Command Codes Functions CodesEntering a Setup Code VOLBefore operation OperationsListening to a Program Source Video 1 Video 2 Video 3 VideoSelect the tone mode as desired When CD, Tape MON or Video 1~ Video 4 is selectedAdjusting the tone bass and treble Select the digital or the analog input as DesiredWhen listening to DTS, Dolby Digital or Mpeg Program sources, if the headphones are pluggedEnsure that the Speaker button is set to off Surround Sound Surround modesTheater Speaker placement Front left and right speakers and center speakerEnjoying Surround Sound Necessary decoding process for optimum surround modesRPT Extra Surr Title Adjusting each channel level Adjusting each channel level with testTone Downmixing into 2 front channels Presetting radio stations Auto tuningManual tuning Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceRecording with Tape Monitor Dubbing the sound and image signalsRecording Dubbing from video components ontoConnected, Digital is flickering. There Digital Audio Recording with MD RecorderInput is selected as follows Will be no recording as well as no soundOther Functions Operating the sleep timerAdjusting the brightness of the fluorescent displays Compressing the dynamic range Dolby Digital sources onlyEntering a video label Correcting or clearing a video labelRoom 2 Source Playback Using the OSD OSD Menu SettingsCurrent Status Display When selecting the Speaker Setup Select the desired menu using the Cursor UP , Down buttonsWhen selecting the CH Level Trim When selecting the Surround SetupSetting the Speaker Setup When selecting the Speaker ConfigPress the Cursor UP When selecting the Speaker Distance Enter buttonWhen selecting the LFE Level Control Buttons to select the desired LFE level modeSetting the Function Select When selecting the Input SetupPress the Cursor UP /DOWN Press the Cursor Left Treble cannot be adjusted When selecting the Tone ControlOff Select this when adjusting tone for your taste Changes as followsWhen selecting the OSD Mode On To turn on the current status displayOff To turn off the current status display Setting the Surround Setup When selecting the Source DirectWhen selecting the Cinema EQ When selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Function Select for Room Room 2 Feed mode to Off to save electricityRoom 2 source cannot be selected Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section863
Top Page Image Contents