Sherwood R-863 manual Entering a Setup Code, Vol

Page 14

ENGLISH

ENTERING A SETUP CODE

•This remote control can control up to eight different components.

•Before operating audio and video components using the remote control supplied with this receiver, the setup code for each component should be entered.

•Because only the setup codes for CD player and DVD player among Sherwood components are listed in the operating manual of this remote control, when entering a setup code for Sherwood components for system remote control operation, find the corresponding setup code in the “FUNCTION TABLE of the NUMBERED BUTTONS” on page 11 in this operating instructions. For your reference, the setup cord for each Sherwood component such as CD player, tape deck and DVD player(V-756, etc.) is “001” respectively.(However, the setup code for some Sherwood DVD player such as VD-4103, etc. is “057”, “074”, “112”, “114”.) Enter each setup code for CD player and tape

deck doing steps , and

as follows.

 

 

 

 

 

 

1

Turn on the component you want to control.

2

Find the setup code for your component

 

 

referring to “Set-Up Code Table” in the

 

 

 

 

 

 

 

 

operating manual of this remote control.

Example) When entering the setup code for this

Example) The correct setup code for this receiver is

 

receiver, turn on this receiver.

 

“001”.

 

 

 

 

3

Press the corresponding DEVICE and the

4

Enter the 3 digit setup code aiming the remote control

MUTE buttons simultaneously.

at the REMOTE SENSOR on the component.

 

For receiver or amplifier :

For

"001" :

0

0

1

 

 

 

 

 

 

 

 

 

For CD player

:

 

 

 

 

 

 

 

 

 

For

"102" :

1

0

2

 

 

For CABLE

:

 

 

 

 

 

 

 

 

 

Your component will be turned off when the correct

 

 

 

setup code is entered.

 

 

Then the LED lamp and the corresponding DEVICE

Continue to enter the corresponding codes until your

component turns off.

 

 

button on the remote control light up for 20 seconds.

If the LED lamp and the corresponding DEVICE

 

 

 

button go off, start from the step again.

 

5

Press the corresponding DEVICE button to

6

Operate the component using the

 

store the setup code.

corresponding function buttons on the remote

 

 

 

 

 

 

control such as POWER, CH

and

 

 

 

 

VOL

 

buttons, etc.

 

 

For receiver or amplifier :

If any of the buttons do not perform as they should

 

For CD player

:

start from step

 

again to enter the next setup code.

 

Note:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Some audio and video components have separate

 

 

 

buttons for POWER ON/OFF.

 

 

 

For CABLE

:

In this case, press the corresponding DEVICE button

 

 

 

to turn the component ON and press the POWER

 

 

 

button to turn the component OFF.

 

 

 

 

If there is no correct setup code or if the

 

Then the LED lamp and the corresponding DEVICE

Manufacturer/Brand for your component is not listed

button will flicker twice.

in “Set-Up Code Table” in the operating manual of

 

 

 

this remote control, please use the “Auto Search

 

 

 

Method” on page 10 in the operating manual of this

7

Repeat the above steps to for each

remote control.

 

 

 

 

Although each setup code is designed to work with

of your other components.

many different modes, certain codes may not work with

 

 

some models. (Also, certain codes may only operate

 

 

 

some of the functions available on a given model.)

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 863 Unpacking and Installation IntroductionRead this Before Operating Your Unit Introduction Connecting Audio Components System ConnectionsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Front Panel Controls Dynamic Range ButtonThis remote control has 3 operating modes as follows Universal Remote ControlsDigi Link System Remote Controls Function Table of the Numbered Buttons Matching the polarity Loading BatteriesRemove the cover Additional Information on Remote Command Codes Functions CodesEntering a Setup Code VOLBefore operation OperationsListening to a Program Source Video 1 Video 2 Video 3 VideoSelect the tone mode as desired When CD, Tape MON or Video 1~ Video 4 is selectedAdjusting the tone bass and treble Select the digital or the analog input as DesiredEnsure that the Speaker button is set to off When listening to DTS, Dolby Digital or MpegProgram sources, if the headphones are plugged Surround Sound Surround modesTheater Speaker placement Front left and right speakers and center speakerEnjoying Surround Sound Necessary decoding process for optimum surround modesRPT Extra Surr Title Tone Adjusting each channel levelAdjusting each channel level with test Downmixing into 2 front channels Presetting radio stations Auto tuningManual tuning Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceRecording with Tape Monitor Dubbing the sound and image signalsRecording Dubbing from video components ontoConnected, Digital is flickering. There Digital Audio Recording with MD RecorderInput is selected as follows Will be no recording as well as no soundOther Functions Operating the sleep timerAdjusting the brightness of the fluorescent displays Compressing the dynamic range Dolby Digital sources onlyEntering a video label Correcting or clearing a video labelRoom 2 Source Playback Current Status Display Using the OSDOSD Menu Settings When selecting the Speaker Setup Select the desired menu using the Cursor UP , Down buttonsWhen selecting the CH Level Trim When selecting the Surround SetupPress the Cursor UP Setting the Speaker SetupWhen selecting the Speaker Config When selecting the Speaker Distance Enter buttonWhen selecting the LFE Level Control Buttons to select the desired LFE level modePress the Cursor UP /DOWN Setting the Function SelectWhen selecting the Input Setup Press the Cursor Left Treble cannot be adjusted When selecting the Tone ControlOff Select this when adjusting tone for your taste Changes as followsOff To turn off the current status display When selecting the OSD ModeOn To turn on the current status display When selecting the Cinema EQ Setting the Surround SetupWhen selecting the Source Direct When selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeRoom 2 source cannot be selected When selecting the Function Select for RoomRoom 2 Feed mode to Off to save electricity Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section863
Top Page Image Contents