Sherwood R-863 manual Additional Information on Remote Command Codes, Functions Codes

Page 13

ADDITIONAL INFORMATION ON REMOTE COMMAND CODES

•This receiver recognizes and responds to IR codes that are not transmitted by the supplied remote control unit. These commands and their corresponding functions, shown on the following table, are made available for custom installers and advanced hobbysts who are already familiar with the programming of such devices as the Crestron Touch Screen and the Philps Pronto.

Custom Code : 8345H(NEC)

FUNCTIONS	CODES	FUNCTIONS	CODES

DTS	70H	DSP MODE	5CH

Dolby Digital	71H	VIDEO 1	56H

EXTRA SURROUND 6.1/7.1	44H	VIDEO 2	5AH

DECODING MODE	58H	VIDEO 3	07H

STEREO	4FH	VIDEO 4	5BH

DIGITAL/ANALOG	E1H	TUNER	03H

Dolby Pro Logic II Movie	E8H	TAPE MONITOR	06H

Dolby Pro Logic II Music	E9H	AUX	0AH

DTS Neo Movie	EDH	CD	0BH

DTS Neo Music	EEH	7.1 CH DIRECT	4AH

MPEG	EBH	SOURCE DIRECT	7BH

PCM	EFH

13

ENGLISH

Image 13

Contents 863 Introduction Unpacking and InstallationRead this Before Operating Your Unit Introduction System Connections Connecting Audio ComponentsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Dynamic Range Button Front Panel ControlsDigi Link System Remote Controls Universal Remote ControlsThis remote control has 3 operating modes as follows Function Table of the Numbered Buttons Remove the cover Loading BatteriesMatching the polarity Functions Codes Additional Information on Remote Command CodesVOL Entering a Setup CodeListening to a Program Source OperationsBefore operation Video 1 Video 2 Video 3 VideoAdjusting the tone bass and treble When CD, Tape MON or Video 1~ Video 4 is selectedSelect the tone mode as desired Select the digital or the analog input as DesiredProgram sources, if the headphones are plugged When listening to DTS, Dolby Digital or MpegEnsure that the Speaker button is set to off Surround modes Surround SoundTheater Front left and right speakers and center speaker Speaker placementNecessary decoding process for optimum surround modes Enjoying Surround SoundRPT Extra Surr Title Adjusting each channel level with test Adjusting each channel levelTone Downmixing into 2 front channels Manual tuning Auto tuningPresetting radio stations Listening to Radio BroadcastsScanning preset stations in sequence Tuning to preset stationsRecording Dubbing the sound and image signalsRecording with Tape Monitor Dubbing from video components ontoInput is selected as follows Digital Audio Recording with MD RecorderConnected, Digital is flickering. There Will be no recording as well as no soundAdjusting the brightness of the fluorescent displays Operating the sleep timerOther Functions Compressing the dynamic range Dolby Digital sources onlyCorrecting or clearing a video label Entering a video labelRoom 2 Source Playback OSD Menu Settings Using the OSDCurrent Status Display When selecting the CH Level Trim Select the desired menu using the Cursor UP , Down buttonsWhen selecting the Speaker Setup When selecting the Surround SetupWhen selecting the Speaker Config Setting the Speaker SetupPress the Cursor UP Enter button When selecting the Speaker DistanceButtons to select the desired LFE level mode When selecting the LFE Level ControlWhen selecting the Input Setup Setting the Function SelectPress the Cursor UP /DOWN Press the Cursor Left Off Select this when adjusting tone for your taste When selecting the Tone ControlTreble cannot be adjusted Changes as followsOn To turn on the current status display When selecting the OSD ModeOff To turn off the current status display When selecting the Source Direct Setting the Surround SetupWhen selecting the Cinema EQ When selecting the surround mode When selecting the Decoding ModeSetting the CH Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupRoom 2 Feed mode to Off to save electricity When selecting the Function Select for RoomRoom 2 source cannot be selected Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications863