Sherwood R-863 manual Adjusting each channel level with test, Tone

Page 23

Adjusting each channel level

 

4

Adjust the level of the selected channel

 

as desired.

 

 

 

If you have performed the CH LEVEL TRIM

 

 

 

 

 

 

 

 

 

 

 

 

 

procedure on the OSD menu, you can skip this

 

 

 

 

 

 

procedure. (For details, refer to

“SETTING THE

 

 

 

 

 

 

CH LEVEL TRIM” on page 43.)

 

 

MULTI CONTROL

 

 

 

3

Select the desired channel.

 

 

 

 

 

CH LEVEL

 

 

 

 

 

 

 

or

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CHANNEL

 

CH SEL

 

DOWN

 

UP

 

 

 

 

 

 

 

 

 

 

 

 

 

SELECTOR

 

 

 

 

 

 

 

 

 

 

 

or

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If the channel display disappears, start from the

 

 

 

 

 

 

above step

again.

 

 

 

Each time this button is pressed, the corresponding

 

 

 

 

 

 

channel is selected and displayed for 3 seconds as

 

 

 

 

 

 

follows:

 

 

 

 

 

5

Repeat the above steps

and

to

FRONT-L

CENTER(or FRONT-C)

FRONT-R SURR-R

adjust each channel level until the sound

SUBWOOFER

SURR-L (( SURR-C) or (

BACK-L

BACK-R))

level of each speaker is heard to be

Depending on the speaker setting, items set to None

 

equally loud.

 

 

 

 

 

 

 

 

 

or No can not be selected.

 

 

 

 

 

 

 

 

 

Adjusting each channel level with test

7

At each channel, adjust the level as

tone

 

 

 

 

 

desired until the sound level of each

Only when playing a program source in available

speaker is heard to be equally loud.

 

 

 

 

 

 

surround modes except the DOLBY VIRTUAL

 

 

 

 

 

 

mode, the volume level of each channel can be

 

MULTI CONTROL

 

 

 

adjusted easily with the test tone function.

 

 

 

 

 

 

 

Note : When the 7.1 CH DIRECT is selected as an

 

 

 

 

CH LEVEL

 

 

or

 

 

 

input source, the test tone function does not

 

 

 

 

 

work.

 

 

 

 

 

 

 

 

 

 

6

Enter the test tone mode.

 

DOWN

 

UP

 

 

 

TEST TONE

 

 

 

You can select the desired channel and adjust its level

 

 

 

 

 

 

or

 

 

 

with repeating the steps

and

in “Adjusting each

 

 

 

 

 

channel level” procedure.

 

 

 

 

 

 

 

TEST

 

 

 

 

 

 

 

 

 

 

 

TONE

 

 

 

 

 

 

 

 

 

 

 

 

 

8

Cancel the test tone function.

 

The test tone will be heard from the speaker of each

 

 

 

 

 

channel for 2 seconds as follows:

 

 

 

 

 

 

 

Front Left

Center Front Right

Surround Right

 

 

TEST TONE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Surround Left ((

Surround Center) or (

Back Left

Back Right))

 

 

or

 

 

 

SUBwoofer

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TEST

 

 

 

 

 

 

 

 

 

 

 

TONE

 

Depending on the speaker setting (None or No), the test tone of the corresponding channel is not available.

ENGLISH

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents 863 Introduction Unpacking and InstallationRead this Before Operating Your Unit Introduction System Connections Connecting Audio ComponentsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Dynamic Range Button Front Panel ControlsThis remote control has 3 operating modes as follows Universal Remote ControlsDigi Link System Remote Controls Function Table of the Numbered Buttons Matching the polarity Loading BatteriesRemove the cover Functions Codes Additional Information on Remote Command CodesVOL Entering a Setup CodeVideo 1 Video 2 Video 3 Video OperationsListening to a Program Source Before operationSelect the digital or the analog input as Desired When CD, Tape MON or Video 1~ Video 4 is selectedAdjusting the tone bass and treble Select the tone mode as desiredEnsure that the Speaker button is set to off When listening to DTS, Dolby Digital or MpegProgram sources, if the headphones are plugged Surround modes Surround SoundTheater Front left and right speakers and center speaker Speaker placementNecessary decoding process for optimum surround modes Enjoying Surround SoundRPT Extra Surr Title Tone Adjusting each channel levelAdjusting each channel level with test Downmixing into 2 front channels Listening to Radio Broadcasts Auto tuningManual tuning Presetting radio stationsScanning preset stations in sequence Tuning to preset stationsDubbing from video components onto Dubbing the sound and image signalsRecording Recording with Tape MonitorWill be no recording as well as no sound Digital Audio Recording with MD RecorderInput is selected as follows Connected, Digital is flickering. ThereCompressing the dynamic range Dolby Digital sources only Operating the sleep timerAdjusting the brightness of the fluorescent displays Other FunctionsCorrecting or clearing a video label Entering a video labelRoom 2 Source Playback Current Status Display Using the OSDOSD Menu Settings When selecting the Surround Setup Select the desired menu using the Cursor UP , Down buttonsWhen selecting the CH Level Trim When selecting the Speaker SetupPress the Cursor UP Setting the Speaker SetupWhen selecting the Speaker Config Enter button When selecting the Speaker DistanceButtons to select the desired LFE level mode When selecting the LFE Level ControlPress the Cursor UP /DOWN Setting the Function SelectWhen selecting the Input Setup Press the Cursor Left Changes as follows When selecting the Tone ControlOff Select this when adjusting tone for your taste Treble cannot be adjustedOff To turn off the current status display When selecting the OSD ModeOn To turn on the current status display When selecting the Cinema EQ Setting the Surround SetupWhen selecting the Source Direct When selecting the surround mode When selecting the Decoding ModeSetting the CH Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupRoom 2 source cannot be selected When selecting the Function Select for RoomRoom 2 Feed mode to Off to save electricity Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications863
Top Page Image Contents