Sherwood R-863 manual Press the Cursor Left

Page 38

ENGLISH

Press the CURSOR LEFT(

4

VOL. CH LEVEL

HOME THEATER MASTER

RNC-220

)/RIGHT( ) buttons to select the desired DIGITAL IN.

Each time these buttons are pressed, the DIGITAL INs change. Notes:

Because there are 5 DIGITAL INs on the rear and front panels, one of CD, TAPE MONITOR and VIDEO 1~4 cannot be matched a DIGITAL IN to.

In this case, you do select “None” instead of a DIGITAL IN.

When the input source set to “None” is selected, the analog input is automatically selected.

In such a case that a DIGITAL IN is matched to two input sources or more, when these input sources are selected, the digital audio signals can be heard from the same DIGITAL IN.

5

Repeat the above steps

and

until the connected DIGITAL INs are matched to the desired input

sources respectively.

 

 

When selecting the VIDEO SELECT

You can also select a video input source on the OSD menu and enjoy it without pressing the VIDEO SELECTOR button(s).

Press the CURSOR UP( )/DOWN( ) buttons to select the VIDEO SELECT, then press the ENTER

2

button.

 

 

 

 

V I D E O S E L E C T

 

VOL. CH LEVEL

 

 

 

ENTER

V I D E O I N :

VID 1

 

 

R E T U R N : B a c k

, : S e l e c t

 

HOME THEATER MASTER

 

 

 

RNC-220

 

 

Press the CURSOR LEFT( )/RIGHT( ) buttons to select the desired video input source.

3

VOL. CH LEVEL

HOME THEATER MASTER

RNC-220

Each time these buttons are pressed, the video input source changes.

38

Image 38
Contents 863 Unpacking and Installation IntroductionRead this Before Operating Your Unit Introduction Connecting Audio Components System ConnectionsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Front Panel Controls Dynamic Range ButtonThis remote control has 3 operating modes as follows Universal Remote ControlsDigi Link System Remote Controls Function Table of the Numbered Buttons Matching the polarity Loading BatteriesRemove the cover Additional Information on Remote Command Codes Functions CodesEntering a Setup Code VOLBefore operation OperationsListening to a Program Source Video 1 Video 2 Video 3 VideoSelect the tone mode as desired When CD, Tape MON or Video 1~ Video 4 is selectedAdjusting the tone bass and treble Select the digital or the analog input as DesiredEnsure that the Speaker button is set to off When listening to DTS, Dolby Digital or MpegProgram sources, if the headphones are plugged Surround Sound Surround modesTheater Speaker placement Front left and right speakers and center speakerEnjoying Surround Sound Necessary decoding process for optimum surround modesRPT Extra Surr Title Tone Adjusting each channel levelAdjusting each channel level with test Downmixing into 2 front channels Presetting radio stations Auto tuningManual tuning Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceRecording with Tape Monitor Dubbing the sound and image signalsRecording Dubbing from video components ontoConnected, Digital is flickering. There Digital Audio Recording with MD RecorderInput is selected as follows Will be no recording as well as no soundOther Functions Operating the sleep timerAdjusting the brightness of the fluorescent displays Compressing the dynamic range Dolby Digital sources onlyEntering a video label Correcting or clearing a video labelRoom 2 Source Playback Current Status Display Using the OSDOSD Menu Settings When selecting the Speaker Setup Select the desired menu using the Cursor UP , Down buttonsWhen selecting the CH Level Trim When selecting the Surround SetupPress the Cursor UP Setting the Speaker SetupWhen selecting the Speaker Config When selecting the Speaker Distance Enter buttonWhen selecting the LFE Level Control Buttons to select the desired LFE level modePress the Cursor UP /DOWN Setting the Function SelectWhen selecting the Input Setup Press the Cursor Left Treble cannot be adjusted When selecting the Tone ControlOff Select this when adjusting tone for your taste Changes as followsOff To turn off the current status display When selecting the OSD ModeOn To turn on the current status display When selecting the Cinema EQ Setting the Surround SetupWhen selecting the Source Direct When selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeRoom 2 source cannot be selected When selecting the Function Select for RoomRoom 2 Feed mode to Off to save electricity Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section863