Sherwood R-863 manual Setting the Surround Setup, When selecting the Source Direct

Page 41

SETTING THE SURROUND SETUP

S U R R O U N D S E T U P

 

 

S O U R C E D I R E C T

:

 

Off

 

 

 

 

To select the source direct function for pure sound quality or not.

 

 

 

 

 

D E C O D I N G M O D E

:

 

AUTO

 

 

 

To select the desired decoding mode.

 

 

 

D O L B Y D I G I T A L

 

 

 

 

 

 

 

To select the desired surround mode.

 

 

 

 

 

 

 

C I N E M A E Q :

Off

 

 

 

 

 

 

To select the cinema EQ function or not.

 

 

 

 

 

 

R E T U R N : B a c k

,

 

: S e l e c t

 

 

Notes :

Only when the digital input is selected as signal input, the decoding mode and the surround mode can both be selected as desired.

When the analog input is selected, only the surround mode can be selected.

Press the CURSOR UP(

)/DOWN( ) buttons to select the desired item.

1

Each time these buttons are pressed, “ ” and “ ” are

 

moved to the corresponding mode.

Press the CURSOR LEFT( )/RIGHT( ) buttons to select the desired mode.

2

Each time these buttons are pressed, the modes change as follows according to the selected item :

When selecting the SOURCE DIRECT

Only when playing program sources in analog stereo or digital 2 ch PCM format, the SOURCE DIRECT can be selected. On : Select this to achieve the pure sound quality.

When this is selected, the stereo mode is automatically selected and the pure sound that bypasses the tone circuitry will be heard.

Off : Select this to cancel the source direct function. Notes :

When the SOURCE DIRECT is set to On, DECODING MODE, surround mode and CINEMA EQ cannot be selected. When you select the 7.1 CH DIRECT as input source or the digital signals from DTS, Dolby Digital or MPEG sources, etc. are input, the source direct function is automatically canceled.

When selecting the CINEMA EQ

When 96 kHz PCM(2 channel stereo) signals are input or the source direct function is selected, the cinema EQ function can not be selected.

On : Select this to compensate for edgy or shrill movie sound tracks.

Off : Select this to cancel the cinema EQ function.

41

ENGLISH

Image 41
Contents 863 Introduction Unpacking and InstallationRead this Before Operating Your Unit Introduction System Connections Connecting Audio ComponentsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Dynamic Range Button Front Panel ControlsThis remote control has 3 operating modes as follows Universal Remote ControlsDigi Link System Remote Controls Function Table of the Numbered Buttons Matching the polarity Loading BatteriesRemove the cover Functions Codes Additional Information on Remote Command CodesVOL Entering a Setup CodeListening to a Program Source OperationsBefore operation Video 1 Video 2 Video 3 VideoAdjusting the tone bass and treble When CD, Tape MON or Video 1~ Video 4 is selectedSelect the tone mode as desired Select the digital or the analog input as DesiredEnsure that the Speaker button is set to off When listening to DTS, Dolby Digital or MpegProgram sources, if the headphones are plugged Surround modes Surround SoundTheater Front left and right speakers and center speaker Speaker placementNecessary decoding process for optimum surround modes Enjoying Surround SoundRPT Extra Surr Title Tone Adjusting each channel levelAdjusting each channel level with test Downmixing into 2 front channels Manual tuning Auto tuningPresetting radio stations Listening to Radio BroadcastsScanning preset stations in sequence Tuning to preset stationsRecording Dubbing the sound and image signalsRecording with Tape Monitor Dubbing from video components ontoInput is selected as follows Digital Audio Recording with MD RecorderConnected, Digital is flickering. There Will be no recording as well as no soundAdjusting the brightness of the fluorescent displays Operating the sleep timerOther Functions Compressing the dynamic range Dolby Digital sources onlyCorrecting or clearing a video label Entering a video labelRoom 2 Source Playback Current Status Display Using the OSDOSD Menu Settings When selecting the CH Level Trim Select the desired menu using the Cursor UP , Down buttonsWhen selecting the Speaker Setup When selecting the Surround SetupPress the Cursor UP Setting the Speaker SetupWhen selecting the Speaker Config Enter button When selecting the Speaker DistanceButtons to select the desired LFE level mode When selecting the LFE Level ControlPress the Cursor UP /DOWN Setting the Function SelectWhen selecting the Input Setup Press the Cursor Left Off Select this when adjusting tone for your taste When selecting the Tone ControlTreble cannot be adjusted Changes as followsOff To turn off the current status display When selecting the OSD ModeOn To turn on the current status display When selecting the Cinema EQ Setting the Surround SetupWhen selecting the Source Direct When selecting the surround mode When selecting the Decoding ModeSetting the CH Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupRoom 2 source cannot be selected When selecting the Function Select for RoomRoom 2 Feed mode to Off to save electricity Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications863