Sherwood R-863 manual Tuning to preset stations, Scanning preset stations in sequence

Page 26

ENGLISH

3

Select the desired preset number(1~30)

4

Repeat the above steps

to to

and press the MEMORY/ENTER button.

memorize other stations.

 

 

TUNING/PRESET

MEMO/ENTER

 

 

 

 

 

 

 

 

 

 

 

 

 

MEMORY BACKUP FUNCTION

When using the NUMERIC buttons on the remote

The following items, set before the receiver is turned

control.

 

 

 

 

off, are memorized.

 

Examples)

 

 

 

INPUT SELECTOR settings

 

 

 

 

 

For “3” :

 

Surround mode settings

 

 

within 2 seconds

 

Preset stations, etc.

 

For “15” :

 

 

 

 

 

 

 

 

 

 

Note : If the electricity fails or the AC input cord is

For “30” :

 

 

disconnected for about 2 weeks, all

The station has now been stored in the memory.

 

memorized settings will be lost.

When using the NUMERIC buttons, the station is stored

 

 

 

 

automatically without pressing the MEMORY/ ENTER

 

 

 

 

button.

 

 

 

 

 

 

A stored frequency is erased from the memory by storing

 

 

 

 

another frequency in its place.

 

 

 

 

 

If “MEMO” goes off, start again from the above step .

 

 

 

 

Tuning to preset stations

2

Select the desired preset number.

 

 

 

 

 

 

 

TUNING/PRESET

 

1

After selecting the tuner as input source,

 

 

 

select the preset tuning mode.

 

 

 

 

 

 

 

When using the NUMERIC buttons on the remote

 

T/P MODE

 

control.

 

 

 

 

 

Examples)

 

 

 

 

 

For “3”:

 

 

 

 

 

For “15”:

within 2 seconds

 

 

 

 

 

 

 

 

 

 

 

within 2 seconds

 

 

 

 

For “30”:

(or

)

Then “PRESET” lights up.

 

When selecting the desired preset number with the

 

 

 

NUMERIC buttons, the desired preset station will be

 

 

 

tuned to automatically without selecting the preset

 

 

 

tuning mode.

 

 

Scanning preset stations in sequence

 

The receiver will start scanning the stations in the

 

preset sequence and each station is received for 5

DISC

seconds.

At the desired station, press this button again to

P.SCAN

 

stop scanning.

26

Image 26
Contents 863 Unpacking and Installation IntroductionRead this Before Operating Your Unit Introduction Connecting Audio Components System ConnectionsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Front Panel Controls Dynamic Range ButtonThis remote control has 3 operating modes as follows Universal Remote ControlsDigi Link System Remote Controls Function Table of the Numbered Buttons Matching the polarity Loading BatteriesRemove the cover Additional Information on Remote Command Codes Functions CodesEntering a Setup Code VOLBefore operation OperationsListening to a Program Source Video 1 Video 2 Video 3 VideoSelect the tone mode as desired When CD, Tape MON or Video 1~ Video 4 is selectedAdjusting the tone bass and treble Select the digital or the analog input as DesiredEnsure that the Speaker button is set to off When listening to DTS, Dolby Digital or MpegProgram sources, if the headphones are plugged Surround Sound Surround modesTheater Speaker placement Front left and right speakers and center speakerEnjoying Surround Sound Necessary decoding process for optimum surround modesRPT Extra Surr Title Tone Adjusting each channel levelAdjusting each channel level with test Downmixing into 2 front channels Presetting radio stations Auto tuningManual tuning Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceRecording with Tape Monitor Dubbing the sound and image signalsRecording Dubbing from video components ontoConnected, Digital is flickering. There Digital Audio Recording with MD RecorderInput is selected as follows Will be no recording as well as no soundOther Functions Operating the sleep timerAdjusting the brightness of the fluorescent displays Compressing the dynamic range Dolby Digital sources onlyEntering a video label Correcting or clearing a video labelRoom 2 Source Playback Current Status Display Using the OSDOSD Menu Settings When selecting the Speaker Setup Select the desired menu using the Cursor UP , Down buttonsWhen selecting the CH Level Trim When selecting the Surround SetupPress the Cursor UP Setting the Speaker SetupWhen selecting the Speaker Config When selecting the Speaker Distance Enter buttonWhen selecting the LFE Level Control Buttons to select the desired LFE level modePress the Cursor UP /DOWN Setting the Function SelectWhen selecting the Input Setup Press the Cursor Left Treble cannot be adjusted When selecting the Tone ControlOff Select this when adjusting tone for your taste Changes as followsOff To turn off the current status display When selecting the OSD ModeOn To turn on the current status display When selecting the Cinema EQ Setting the Surround SetupWhen selecting the Source Direct When selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeRoom 2 source cannot be selected When selecting the Function Select for RoomRoom 2 Feed mode to Off to save electricity Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section863