Sherwood R-863 manual Read this Before Operating Your Unit

Page 3

READ THIS BEFORE OPERATING YOUR UNIT

FOR U.S.A AND CANADA

.......................................120 V

FOR YOUR SAFETY

Units shipped to the U.S.A and Canada are designed for operation on 120 Volts AC only.

Observe all safety precautions for use of a polarized AC plug. However, some products may be supplied with a non polarized plug.

CAUTION: To prevent electric shock, match wide blade of plug to wide slot, insert fully.

FOR EUROPE AND AUSTRALIA

230V/240V

FOR YOUR SAFETY

Units shipped to Australia are designed for operation on 240 V AC only.

To ensure safe operation, the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth.

Improper extension cords are a major cause of fatalities. The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is completely safe. For your safety, if in any doubt about the effective earthing of the power point, consult a qualified electrician.

PAN-EUROPEAN UNIFIED VOLTAGE

All units are suitable for use on supplies 230-240 V AC.

FOR OTHER COUNTRIES

115 V/230 V

FOR YOUR SAFETY

Units shipped to countries other than the above countries are equipped with an AC voltage selector switch on the rear panel. Refer to the following paragraph for the proper setting of this switch.

AC VOLTAGE SELECTION

This unit operates on 115/230 V AC. The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line voltage. If not, it must be set to your voltage in accordance with the following direction.

AC voltage selector switch

AC 230 V				AC 115 V

Move switch lever to match your line voltage with a small screwdriver or other pointed tool.

ENGLISH

3

Image 3

Contents 863 Introduction Unpacking and InstallationRead this Before Operating Your Unit Introduction System Connections Connecting Audio ComponentsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Dynamic Range Button Front Panel ControlsUniversal Remote Controls Digi Link System Remote ControlsThis remote control has 3 operating modes as follows Function Table of the Numbered Buttons Loading Batteries Remove the coverMatching the polarity Functions Codes Additional Information on Remote Command CodesVOL Entering a Setup CodeVideo 1 Video 2 Video 3 Video OperationsListening to a Program Source Before operationSelect the digital or the analog input as Desired When CD, Tape MON or Video 1~ Video 4 is selectedAdjusting the tone bass and treble Select the tone mode as desiredWhen listening to DTS, Dolby Digital or Mpeg Program sources, if the headphones are pluggedEnsure that the Speaker button is set to off Surround modes Surround SoundTheater Front left and right speakers and center speaker Speaker placementNecessary decoding process for optimum surround modes Enjoying Surround SoundRPT Extra Surr Title Adjusting each channel level Adjusting each channel level with testTone Downmixing into 2 front channels Listening to Radio Broadcasts Auto tuningManual tuning Presetting radio stationsScanning preset stations in sequence Tuning to preset stationsDubbing from video components onto Dubbing the sound and image signalsRecording Recording with Tape MonitorWill be no recording as well as no sound Digital Audio Recording with MD RecorderInput is selected as follows Connected, Digital is flickering. ThereCompressing the dynamic range Dolby Digital sources only Operating the sleep timerAdjusting the brightness of the fluorescent displays Other FunctionsCorrecting or clearing a video label Entering a video labelRoom 2 Source Playback Using the OSD OSD Menu SettingsCurrent Status Display When selecting the Surround Setup Select the desired menu using the Cursor UP , Down buttonsWhen selecting the CH Level Trim When selecting the Speaker SetupSetting the Speaker Setup When selecting the Speaker ConfigPress the Cursor UP Enter button When selecting the Speaker DistanceButtons to select the desired LFE level mode When selecting the LFE Level ControlSetting the Function Select When selecting the Input SetupPress the Cursor UP /DOWN Press the Cursor Left Changes as follows When selecting the Tone ControlOff Select this when adjusting tone for your taste Treble cannot be adjustedWhen selecting the OSD Mode On To turn on the current status displayOff To turn off the current status display Setting the Surround Setup When selecting the Source DirectWhen selecting the Cinema EQ When selecting the surround mode When selecting the Decoding ModeSetting the CH Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupWhen selecting the Function Select for Room Room 2 Feed mode to Off to save electricityRoom 2 source cannot be selected Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications863