Sherwood R-863 manual Connecting MULTI-ROOM System KIT

Page 8

ENGLISH

■ROOM 2 connections

Another room

Monitor TV

VIDEO IN

	VIDEO	Speakers
	IN	Speakers
	IN

	A/V receiver
AUDIO IN	or amplifier

• If another A/V receiver or integrated amplifier, etc. is connected to these jacks, you can play a different program source in another room as well as one source in the main room at the same time.(For details, refer to "ROOM 2 SOURCE PLAYBACK" on page 31).

• When the multiroom adaptor is connected to control this unit in another room, the ROOM 2 function is more convenient.

Note:

• To minimize hum or noise, use high quality connection cords in such a way that there is no humming or noise.

■ CONNECTING MULTI-ROOM

SYSTEM KIT

Another room

OUT

Adaptor	IR receiver	Remote control unit
(Multi-room system kit)	(Multi room system kit)

•To control this unit from a remote location, connect this jack to the output of the multi-room adaptor.

For information on the multi-room system kit, contact the Xantech corporation at 1-800-843-5465 or www.xantech.com.

■CONNECTING SPEAKERS

Front right

Front left

Surround right

Surround back right

Front center

Surround left

Surround back left

■SWITCHED AC OUTLETS

•These outlets are switched on(power-on mode) and off(standby mode) according to the power control as follows(Maximum total capacity is 1A, 100W):

Standby mode – switched AC outlet off Power-on mode – switched AC outlet on

■AC INLET

Plug the supplied AC input cord into this AC INLET and then into the wall AC outlet.

•Never short circuit the + and - speaker wires.

•Be sure to connect speakers firmly and correctly according to the channel (left and right ) and the polarity ( + and -).

•Be sure to use speakers with the impedance of over 6 Ω.

•Only when enjoying either 6.1 or 7.1 channel surround playback, connect the surround back left speaker only or both of surround

back speakers. Note:

•After installing the speakers, first set the connected speakers to the desired before operating this receiver.(For details, refer to "SETTING THE SPEAKER SETUP" on page 34.)

To a wall AC outlet.

•Do not use an AC input cord other than the one supplied with this unit. The AC input cord supplied is designed for use with this unit and should not be used with any other device.

8

Image 8

Contents 863 Unpacking and Installation IntroductionRead this Before Operating Your Unit Introduction Connecting Audio Components System ConnectionsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Front Panel Controls Dynamic Range ButtonThis remote control has 3 operating modes as follows Universal Remote ControlsDigi Link System Remote Controls Function Table of the Numbered Buttons Matching the polarity Loading BatteriesRemove the cover Additional Information on Remote Command Codes Functions CodesEntering a Setup Code VOLOperations Listening to a Program SourceBefore operation Video 1 Video 2 Video 3 VideoWhen CD, Tape MON or Video 1~ Video 4 is selected Adjusting the tone bass and trebleSelect the tone mode as desired Select the digital or the analog input as DesiredEnsure that the Speaker button is set to off When listening to DTS, Dolby Digital or MpegProgram sources, if the headphones are plugged Surround Sound Surround modesTheater Speaker placement Front left and right speakers and center speakerEnjoying Surround Sound Necessary decoding process for optimum surround modesRPT Extra Surr Title Tone Adjusting each channel levelAdjusting each channel level with test Downmixing into 2 front channels Auto tuning Manual tuningPresetting radio stations Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceDubbing the sound and image signals RecordingRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Input is selected as followsConnected, Digital is flickering. There Will be no recording as well as no soundOperating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Compressing the dynamic range Dolby Digital sources onlyEntering a video label Correcting or clearing a video labelRoom 2 Source Playback Current Status Display Using the OSDOSD Menu Settings Select the desired menu using the Cursor UP , Down buttons When selecting the CH Level TrimWhen selecting the Speaker Setup When selecting the Surround SetupPress the Cursor UP Setting the Speaker SetupWhen selecting the Speaker Config When selecting the Speaker Distance Enter buttonWhen selecting the LFE Level Control Buttons to select the desired LFE level modePress the Cursor UP /DOWN Setting the Function SelectWhen selecting the Input Setup Press the Cursor Left When selecting the Tone Control Off Select this when adjusting tone for your tasteTreble cannot be adjusted Changes as followsOff To turn off the current status display When selecting the OSD ModeOn To turn on the current status display When selecting the Cinema EQ Setting the Surround SetupWhen selecting the Source Direct When selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeRoom 2 source cannot be selected When selecting the Function Select for RoomRoom 2 Feed mode to Off to save electricity Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section863