Sherwood R-863 When selecting the LFE Level Control, Buttons to select the desired LFE level mode

Page 36

ENGLISH

When selecting the LFE LEVEL CONTROL

1

Press the CURSOR UP(

)/DOWN(

) buttons to select the LFE LEVEL CONTROL, then press the

ENTER button.

 

 

 

 

 

 

 

 

 

 

 

L F E L E V E L C O N T R O L

 

 

 

 

ENTER

D O L B Y

----- +

 

0

dB

 

 

 

 

D T S

----- + -----

0

dB

 

 

 

 

M P E G ----- + -----

0

dB

 

 

 

 

R E T U R N : B a c k

, : S e l e c t

2

Press the CURSOR UP(

)/DOWN(

) buttons to select the desired LFE level mode.

 

 

 

 

 

 

 

 

Each time these buttons are pressed, “ ” is moved to the corresponding LFE level mode.

Press the CURSOR LEFT( )/RIGHT( ) buttons to adjust the selected LFE level as desired.

3

Each time these buttons are pressed, the LFE level can be adjusted within the range of either -10~0 dB for Dolby Digital program sources or -10~+10 dB for DTS and MPEG program sources.

In general, we recommend the LFE level for Dolby Digital program sources to be set at 0 dB and +10 dB for DTS program sources.(However, the recommended LFE level for some early DTS program sources is 0 dB.)

If the recommended levels seem too high, lower the setting as necessary.

Repeat the above steps

and

until each level is adjusted as desired.

4

36

Image 36
Contents 863 Unpacking and Installation IntroductionRead this Before Operating Your Unit Introduction Connecting Audio Components System ConnectionsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Front Panel Controls Dynamic Range ButtonUniversal Remote Controls Digi Link System Remote ControlsThis remote control has 3 operating modes as follows Function Table of the Numbered Buttons Loading Batteries Remove the coverMatching the polarity Additional Information on Remote Command Codes Functions CodesEntering a Setup Code VOLOperations Listening to a Program SourceBefore operation Video 1 Video 2 Video 3 VideoWhen CD, Tape MON or Video 1~ Video 4 is selected Adjusting the tone bass and trebleSelect the tone mode as desired Select the digital or the analog input as DesiredWhen listening to DTS, Dolby Digital or Mpeg Program sources, if the headphones are pluggedEnsure that the Speaker button is set to off Surround Sound Surround modesTheater Speaker placement Front left and right speakers and center speakerEnjoying Surround Sound Necessary decoding process for optimum surround modesRPT Extra Surr Title Adjusting each channel level Adjusting each channel level with testTone Downmixing into 2 front channels Auto tuning Manual tuningPresetting radio stations Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceDubbing the sound and image signals RecordingRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Input is selected as followsConnected, Digital is flickering. There Will be no recording as well as no soundOperating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Compressing the dynamic range Dolby Digital sources onlyEntering a video label Correcting or clearing a video labelRoom 2 Source Playback Using the OSD OSD Menu SettingsCurrent Status Display Select the desired menu using the Cursor UP , Down buttons When selecting the CH Level TrimWhen selecting the Speaker Setup When selecting the Surround SetupSetting the Speaker Setup When selecting the Speaker ConfigPress the Cursor UP When selecting the Speaker Distance Enter buttonWhen selecting the LFE Level Control Buttons to select the desired LFE level modeSetting the Function Select When selecting the Input SetupPress the Cursor UP /DOWN Press the Cursor Left When selecting the Tone Control Off Select this when adjusting tone for your tasteTreble cannot be adjusted Changes as followsWhen selecting the OSD Mode On To turn on the current status displayOff To turn off the current status display Setting the Surround Setup When selecting the Source DirectWhen selecting the Cinema EQ When selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeWhen selecting the Function Select for Room Room 2 Feed mode to Off to save electricityRoom 2 source cannot be selected Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section863