Sherwood R-863 manual Listening to Radio Broadcasts, Auto tuning, Manual tuning

Page 25

LISTENING TO RADIO BROADCASTS

Auto tuning

 

Select the desired band.

 

1

Select the tuner.

2 BAND

 

 

 

 

 

 

 

 

 

 

BAND

FREQUENCY

 

 

 

 

 

 

 

Each time this button is pressed, the band changes

 

AUDIO

as follows :

 

 

 

 

VOL. CH LEVEL

 

 

 

 

 

 

or

FM Stereo mode

 

FM Mono mode

AM

 

(“ STEREO” lights up )

( “ STEREO” goes off)

 

 

 

 

 

TUNER

When FM stereo broadcasts are poor because of

 

weak broadcast signals, select the FM mono mode to

 

HOME THEATER MASTER

 

RNC-220

reduce the noise, then FM broadcasts are reproduced

 

 

 

 

in monaural sound.

 

 

 

 

 

When pressing the BAND button without selecting

 

 

the TUNER, the tuner will be selected automatically.

3

Select the tuning mode.

4

Press the TUNING/PRESET UP(

) or

 

DOWN(

) button for more than 0.5 second.

T/P MODE

 

TUNING/PRESET

 

 

 

 

Each time this button is pressed, the mode changes

Then “ AUTO” appears on the display. The tuner

as follows:

will now search until a station of sufficient

 

 

Tuning mode : “PRESET” goes off.

 

 

strength has been found. The display shows the

 

 

Preset mode : “PRESET” lights up.

 

tuned frequency and “TUNED”.

 

 

 

If the station found is not the desired one, simply

 

 

 

 

 

 

 

 

 

 

repeat this operation.

 

 

 

 

 

Weak stations are skipped during auto tuning.

Manual tuning

TUNING/PRESET

Manual tuning is useful when you already know the frequency of the desired transmitter.

Perform the steps ~

in “Auto tuning” procedure and press the

TUNING/PRESET UP(

) or DOWN( )button repeatedly until the right

frequency has been reached.

ENGLISH

Presetting radio stations

You can store up to 30 preferred stations in the memory.

1

Tune in the desired station with auto or

manual tuning.

Press the MEMORY/ENTER button.

2

MEMO/ENTER

“MEMO” is flickering for 5 seconds.

25

Image 25
Contents 863 Introduction Unpacking and InstallationRead this Before Operating Your Unit Introduction System Connections Connecting Audio ComponentsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Dynamic Range Button Front Panel ControlsDigi Link System Remote Controls Universal Remote ControlsThis remote control has 3 operating modes as follows Function Table of the Numbered Buttons Remove the cover Loading BatteriesMatching the polarity Functions Codes Additional Information on Remote Command CodesVOL Entering a Setup CodeListening to a Program Source OperationsBefore operation Video 1 Video 2 Video 3 VideoAdjusting the tone bass and treble When CD, Tape MON or Video 1~ Video 4 is selectedSelect the tone mode as desired Select the digital or the analog input as DesiredProgram sources, if the headphones are plugged When listening to DTS, Dolby Digital or MpegEnsure that the Speaker button is set to off Surround modes Surround SoundTheater Front left and right speakers and center speaker Speaker placementNecessary decoding process for optimum surround modes Enjoying Surround SoundRPT Extra Surr Title Adjusting each channel level with test Adjusting each channel levelTone Downmixing into 2 front channels Manual tuning Auto tuningPresetting radio stations Listening to Radio BroadcastsScanning preset stations in sequence Tuning to preset stationsRecording Dubbing the sound and image signalsRecording with Tape Monitor Dubbing from video components ontoInput is selected as follows Digital Audio Recording with MD RecorderConnected, Digital is flickering. There Will be no recording as well as no soundAdjusting the brightness of the fluorescent displays Operating the sleep timerOther Functions Compressing the dynamic range Dolby Digital sources onlyCorrecting or clearing a video label Entering a video labelRoom 2 Source Playback OSD Menu Settings Using the OSDCurrent Status Display When selecting the CH Level Trim Select the desired menu using the Cursor UP , Down buttonsWhen selecting the Speaker Setup When selecting the Surround SetupWhen selecting the Speaker Config Setting the Speaker SetupPress the Cursor UP Enter button When selecting the Speaker DistanceButtons to select the desired LFE level mode When selecting the LFE Level ControlWhen selecting the Input Setup Setting the Function SelectPress the Cursor UP /DOWN Press the Cursor Left Off Select this when adjusting tone for your taste When selecting the Tone ControlTreble cannot be adjusted Changes as followsOn To turn on the current status display When selecting the OSD ModeOff To turn off the current status display When selecting the Source Direct Setting the Surround SetupWhen selecting the Cinema EQ When selecting the surround mode When selecting the Decoding ModeSetting the CH Level Trim When selecting the Volume Mode Setting the ROOM2 Feed SetupRoom 2 Feed mode to Off to save electricity When selecting the Function Select for RoomRoom 2 source cannot be selected Problem Possible Cause Remedy Troubleshooting GuideAmplifier Section Specifications863