Sherwood R-863 manual Digital Audio Recording with MD Recorder, Input is selected as follows

Page 28

ENGLISH

Start recording on the component hooked

3 up to VIDEO 1.

Start play on the components hooked up to

4 VIDEO 2 and the CD respectively.

The audio signal from the CD and the video signal from the VIDEO 2 component will be dubbed and you can enjoy them on the TV set and from the speakers.

Note: Be sure to observe the order of the above steps and .

DIGITAL AUDIO RECORDING WITH MD RECORDER

Only when the OPTICAL DIGITAL OUT of this receiver is connected to the OPTICAL DIGITAL IN of the MD recorder or CD recorder, you can enjoy high-quality sound of digital recording without converting the original signals. Refer to “ CONNECTING AUDIO COMPONENTS” and “CONNECTING DIGITAL INs and OUT” on page 5 and 7 and the operating instructions of the MD recorder or CD recorder.

Notes:

Digital recording is available for the digital audio program sources such as CDs, MDs, some DVDs, etc. In most DVDs as well as some CDs, etc., digital recording may not be available depending on the signal format.

There are some restrictions on recording digital signals. When making digital recordings, refer to the operating instructions of your digital recording equipment to know what restrictions are imposed.

1

Select a desired input of CD, TAPE

2

For digital recording, select the desired

MONITOR and VIDEO 1~VIDEO 4 as a

digital input as the recording signal input.

recording source.

DIGITAL/ANALOG

 

 

 

INPUT SELECTOR

AUDIO

VIDEO TAPE MON.

VOL. CH LEVEL

 

or

 

Each time this button is pressed, the corresponding

 

 

input is selected as follows:

 

CD

T1/MON

 

DIGITAL

ANALOG

 

 

 

 

VID1 VID2

VID3 VID4

 

 

 

 

HOME THEATER MASTER

 

 

 

 

RNC-220

 

 

 

 

 

Note: When the selected digital input is not

 

 

 

connected, “DIGITAL” is flickering. There

 

 

 

will be no recording as well as no sound.

3

Start recording on the component

Start play on the desired input.

connected to OPTICAL DIGITAL OUT.

4

 

28

Image 28
Contents 863 Unpacking and Installation IntroductionRead this Before Operating Your Unit Introduction Connecting Audio Components System ConnectionsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Front Panel Controls Dynamic Range ButtonDigi Link System Remote Controls Universal Remote ControlsThis remote control has 3 operating modes as follows Function Table of the Numbered Buttons Remove the cover Loading BatteriesMatching the polarity Additional Information on Remote Command Codes Functions CodesEntering a Setup Code VOLOperations Listening to a Program SourceBefore operation Video 1 Video 2 Video 3 VideoWhen CD, Tape MON or Video 1~ Video 4 is selected Adjusting the tone bass and trebleSelect the tone mode as desired Select the digital or the analog input as DesiredProgram sources, if the headphones are plugged When listening to DTS, Dolby Digital or MpegEnsure that the Speaker button is set to off Surround Sound Surround modesTheater Speaker placement Front left and right speakers and center speakerEnjoying Surround Sound Necessary decoding process for optimum surround modesRPT Extra Surr Title Adjusting each channel level with test Adjusting each channel levelTone Downmixing into 2 front channels Auto tuning Manual tuningPresetting radio stations Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceDubbing the sound and image signals RecordingRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Input is selected as followsConnected, Digital is flickering. There Will be no recording as well as no soundOperating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Compressing the dynamic range Dolby Digital sources onlyEntering a video label Correcting or clearing a video labelRoom 2 Source Playback OSD Menu Settings Using the OSDCurrent Status Display Select the desired menu using the Cursor UP , Down buttons When selecting the CH Level TrimWhen selecting the Speaker Setup When selecting the Surround SetupWhen selecting the Speaker Config Setting the Speaker SetupPress the Cursor UP When selecting the Speaker Distance Enter buttonWhen selecting the LFE Level Control Buttons to select the desired LFE level modeWhen selecting the Input Setup Setting the Function SelectPress the Cursor UP /DOWN Press the Cursor Left When selecting the Tone Control Off Select this when adjusting tone for your tasteTreble cannot be adjusted Changes as followsOn To turn on the current status display When selecting the OSD ModeOff To turn off the current status display When selecting the Source Direct Setting the Surround SetupWhen selecting the Cinema EQ When selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeRoom 2 Feed mode to Off to save electricity When selecting the Function Select for RoomRoom 2 source cannot be selected Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section863