Sherwood R-863 manual When CD, Tape MON or Video 1~ Video 4 is selected, Digital Analog

Page 16

ENGLISH

When CD, TAPE MON or VIDEO 1~ VIDEO 4 is selected

Select the digital or the analog input as

4 desired.

DIGITAL/ANALOG

Each time this button is pressed, the corresponding input is selected as follows:

DIGITAL ANALOG

To listen to DTS, Dolby Digital or MPEG program sources in the 2-CH downmix mode, in the stereo mode, the digital input must be selected. (For details, refer to “Downmixing into 2 front channels” on page 24.)

When TUNER or AUX is selected as an input source, the analog input is automatically selected.

Notes:

When the selected digital input is not connected. “DIGITAL” flickers, meaning no sound. (Refer to “ENJOYING SURROUND SOUND” on page 21.)

To select the digital input, you must match the connected DIGITAL IN to the corresponding input source.

(For details, refer to “When selecting the DIGITAL IN SETUP” on page 37.)

Operate the selected component for

5 playback.

When playing back the program sources with surround sound, refer to “ENJOYING SURROUND SOUND” on page 21.

Adjust the (overall) volume.

6

MASTER VOLUME

VOL.

or

DOWNUP

Adjusting the tone (bass and treble)

Select the tone mode as desired.

7

TONE MODE

Each time this button is pressed, the tone mode changes as follows:

BASS TREBLE DEFEAT OFF(or ON)

The tone display is shown for 5 seconds.

If the tone display disappears, press the TONE MODE button again.

( ) : When the tone defeat function is activated (“DEFEAT ON”), bass and treble modes cannot be selected

Note:

When the source direct function is activated, the tone mode cannot be selected.

At the desired tone mode, adjust as

8 desired.

MULTI CONTROL

At the tone defeat mode, each time the MULTI CONTROL knob is rotated, the tone defeat mode changes as follows:

DEFEAT ON : When listening to a program source

without the tone effect.

DEFEAT OFF : When adjusting the tone for your taste.

At the desired tone (bass or treble), each time the MULTI CONTROL knob is rotated, the tone level can be adjusted within the range of +10~ -10 dB. In general, we recommend the bass and treble to be adjusted to 0(flat) level.

To complete tone adjustment, repeat the above steps and .

Extreme settings at high volume may damage your speakers.

16

Image 16
Contents 863 Unpacking and Installation IntroductionRead this Before Operating Your Unit Introduction Connecting Audio Components System ConnectionsConnecting Video Components Connecting System Control Connecting MULTI-ROOM System KIT Front Panel Controls Dynamic Range ButtonDigi Link System Remote Controls Universal Remote ControlsThis remote control has 3 operating modes as follows Function Table of the Numbered Buttons Remove the cover Loading BatteriesMatching the polarity Additional Information on Remote Command Codes Functions CodesEntering a Setup Code VOLOperations Listening to a Program SourceBefore operation Video 1 Video 2 Video 3 VideoWhen CD, Tape MON or Video 1~ Video 4 is selected Adjusting the tone bass and trebleSelect the tone mode as desired Select the digital or the analog input as DesiredProgram sources, if the headphones are plugged When listening to DTS, Dolby Digital or MpegEnsure that the Speaker button is set to off Surround Sound Surround modesTheater Speaker placement Front left and right speakers and center speakerEnjoying Surround Sound Necessary decoding process for optimum surround modesRPT Extra Surr Title Adjusting each channel level with test Adjusting each channel levelTone Downmixing into 2 front channels Auto tuning Manual tuningPresetting radio stations Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceDubbing the sound and image signals RecordingRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Input is selected as followsConnected, Digital is flickering. There Will be no recording as well as no soundOperating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Compressing the dynamic range Dolby Digital sources onlyEntering a video label Correcting or clearing a video labelRoom 2 Source Playback OSD Menu Settings Using the OSDCurrent Status Display Select the desired menu using the Cursor UP , Down buttons When selecting the CH Level TrimWhen selecting the Speaker Setup When selecting the Surround SetupWhen selecting the Speaker Config Setting the Speaker SetupPress the Cursor UP When selecting the Speaker Distance Enter buttonWhen selecting the LFE Level Control Buttons to select the desired LFE level modeWhen selecting the Input Setup Setting the Function SelectPress the Cursor UP /DOWN Press the Cursor Left When selecting the Tone Control Off Select this when adjusting tone for your tasteTreble cannot be adjusted Changes as followsOn To turn on the current status display When selecting the OSD ModeOff To turn off the current status display When selecting the Source Direct Setting the Surround SetupWhen selecting the Cinema EQ When selecting the Decoding Mode When selecting the surround modeSetting the CH Level Trim Setting the ROOM2 Feed Setup When selecting the Volume ModeRoom 2 Feed mode to Off to save electricity When selecting the Function Select for RoomRoom 2 source cannot be selected Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section863