Kenmore 318205869A manual To Set the Clock, To Set the Minute Timer, For a silent control panel

Page 13

Setting Oven Controls

Note: The time of day must first be set in order to operate the oven.

To Set the Clock

When the range is first plugged in, or when the power supply to the range has been interrupted, the display will flash "12:00".

1.Press briefly (do not hold pad down).

2.Within 5 seconds, press and hold the or until the correct time of day appears in the display. Note: The clock cannot be changed during any timed bake or Self-Clean cycle.

To Set the Minute Timer:

1.Press .

2.Press the to increase the time in one minute increments. Press and hold the to increase the time in 10 minute increments. The timer can be set for any amount of time from 1 minute to 11 hours and 59 minutes.

Note: If the pad is pressed first, the timer will advance to 11 hours and 59 minutes.

3.The display shows the timer countdown in minutes until 1 minute remains. Then the display will countdown in seconds.

4.When the set time has run out, the timer will beep 3 times. It will then continue to beep 3 times every 60 seconds until

is pressed.

Note: The indicator light located above the pad will glow while the minute timer is active.

Note: The minute timer does not start or stop cooking. It serves as an extra timer in the kitchen that will beep when the set time has run out. The minute timer can be used alone or during any of the other oven functions. When the minute timer is in use with any other function, the minute timer will be shown in the display. To view other functions, press the pad for that function.

To Change the Minute Timer while it is in use:

While the timer is active and shows in the display, press and hold the or to increase or decrease the time.

To Cancel the Minute Timer before the set time has run out: Press .

Note: To turn the time of day display OFF or ON in the display press and hold for 15 seconds (the control will beep once) and then release. This feature does not remove the set time of day from the memory of the control. When the display is turned OFF the time of day will reappear for a few seconds any time the pad is touched.

For a silent control panel

When choosing a function, a beep will be heard each time a pad is pressed. If desired, the control can be programmed

for silent operation. Press and hold . After 7 seconds, the control will beep once. This will block the controls from

sounding when a pad is pressed. To return the sound, press and hold again for 7 seconds until the control beeps once.

Temperature conversion

The electronic oven control is set to operate in °F (Fahrenheit) when shipped from the factory. The oven can be programmed for any temperature from 170°F to 550°F (77°C to 287°C).

To change the temperature to °C (Celsius) or from °C to °F (control should not be in a Bake or Clean mode):

1.Press . "— —" appears in the display.

2.Press and hold the until "HI" appears in the display.

3.Press and hold until °F or °C appears in the display.

4.Press the or to change °F to °C or °C to °F.

5.Press any control pad to return to normal operating mode.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Kenmore Table of Contents Important Safety Instructions While using the appliance. Do not let clothing Where appliance is in use. They should neverWhen heating fat or grease, watch it closely Do not leave children alone-Children shouldSave These Safety Instructions Conversion to Liquefied Petroleum Gas or L.P. Gas Grounding InstructionsYour Slide-in Range Features At a Glance Slide-in Range FeaturesControl Locations of the Gas Surface Burners Before Setting Surface ControlsSetting Proper Surface Burner Flame Size Setting Surface ControlsOperating the Gas Surface Controls Flame Size Type of CooktopSurface Cooking Using a wokUse Proper Cookware Oven Vent Location Before Setting Oven ControlsRemoving and Replacing Oven Racks Arranging Oven RacksControl Pad Functions Setting Oven ControlsTemperature conversion To Set the Minute TimerTo Change the Minute Timer while it is in use To Set the ClockTo Set Control for Continuous Bake or 12 Hour Energy Saving To Set or Change the Temperature for BakingTo Set Control for Oven Lockout Oven Baking Cooking InformationWhen the Set Bake Time Runs Out To Set the Timed Bake and Delay Start FeaturesBroil Rack Position Table Refer to Fig Food category Setting Oven Controls cont’d To Set for BroilingTo Operate the Oven Light Setting the Warm & Hold FeatureTo set Warm & Hold To set Warm & Hold to turn on automaticallyOven Cleaning Self-CleaningAdjusting the Oven Temperature Self-Clean Time LengthTo Adjust Oven Temperature Cleaning Various Parts of Your Range General Care & CleaningCleaning the Cooktop, Burner Heads, Caps & Grates General Care & Cleaning cont’d3rd Door Hinge locations With oven door fully open Removing and Replacing the Lift-Off Oven DoorTo Remove Oven Door To Replace Oven DoorStorage Drawer Changing Oven LightAppliance must be accessible for Solutions to Common ProblemsService Code error for exemple F11Cleaning cycle Self-cleaning cycle does not workPoor baking results Fan noise during cooking operationProtection Agreements Get it fixed, at your home or ours Cuisinière encastrable Table des matières Emplacementdelaplaque de sérieGarantie sur appareil Kenmore Enregistrement de l’appareilLe faites, un empoisonnement au monoxyde de Entretien par l’usager-Ne réparez pas ou neCarbone pourrait en résulter et l’appareil pourrait Ne modifiez jamais l’appareil, que ce soit enMesures de sécurité importantes Ne laissez jamais les brûleurs sans surveillance Fours autonettoyantsConversion au gaz propane Instructions de mise à la terreFour autonettoyant Caractéristiques de l’appareilEmplacement des commandes des brûleurs de surface Avant de régler les commandes des brûleurs de surfaceRéglage de la bonne dimension de la flamme Réglage des commandes des brûleurs de surfaceEmploi des brûleurs de surface Type de cuissonUstensiles pour la cuisson sur les brûleurs Cuisson sur la table de cuissonUtilisation d’UN wok Installation des grilles Avant de régler les commandes du four suitePosition de l’évent Enlever et replacer les grilles de fourFonctions des touches de la commande du four Réglage de la commande du fourRéglage de lhorloge Pour un tableau de commande silencieuxRéglage de la minuterie Conversion de la températureRéglage de la fonction de verrouillage du four Pour régler la commande du four pour la cuisson au fourPour régler la fonction de verrouillage Cuisson au four Lorsque la durée de cuisson programmée s’est écoulée Catégorie d’aliment Cuisson au grilFonctionnement de la lampe du four Réglage de la fonction Garder ChaudMDRéglage de la fonction Garder ChaudMD Nettoyage du four Cycle autonettoyantPrenez les précautions de nettoyage qui suivent Préparation du four avant le cycle autonettoyantAjustement de la température du four Durée du cycle autonettoyantLa fin du cycle autonettoyant Arrêt ou interruption d’un cycle autonettoyantEntretien général & nettoyage 1er Entretien général & nettoyage suiteEnlever et replacer la porte du four Nettoyage de l’acier inoxydablePour enlever la porte du four Pour replacer la porte du fourTiroir de rangement Remplacement de l’ampoule du fourFacilement. Il doit être accessible Solutions aux problèmes les plus fréquentsLa commande du four sonne et ’appareil n’est pas de niveauLe four dégage beaucoup de fumée La flamme est orangeDurant la cuisson au gril Tion Réglage du four AutonettoyantContrats DE Protection Get it fixed, at your home or ours
Top Page Image Contents