Woods Equipment DS96, DS120 manual Keep Away

Page 12
9 - PN 15503
18865--C

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

(Safety Decals continued from previous page)

5 - PN 18864

DANGER

ROTATING DRIVELINE

CONTACT CAN CAUSE DEATH

KEEP AWAY!

DO NOT OPERATE WITHOUT -

All driveline guards, tractor and equipment shields in place

Drivelines securely attached at both ends

Driveline guards that turn freely on

 

driveline

18864-C

 

8 - PN 18865

WARNING

FALLING OFF CAN RESULT IN BEING RUN OVER.

„Tractor must be equipped with ROPS (or ROPS CAB) and seat belt. Keep foldable ROPS systems in “locked up” position at all times.

„Buckle Up! Keep seat belt securely fastened.

„Allow no riders.

RAISED EQUIPMENT CAN DROP AND CRUSH.

„Before working underneath, follow all instructions and safety rules in operator’s manual and securely block up all corners of equipment with jack stands.

„Securely blocking prevents equipment dropping from hydraulic leak- down, hydraulic system failures or mechanical component failures.

FALLING OFF OR FAILING TO BLOCK SECURELY CAN RESULT IN SERIOUS INJURY OR DEATH.

6 - PN 18866

WARNING￿￿￿￿￿￿ ￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿540￿￿￿￿￿￿￿￿￿￿RPM￿￿￿￿!￿￿￿ ￿￿￿"￿￿#￿￿￿￿￿$

18866-D

7 - PN 18877

WARNING

TO AVOID SERIOUS INJURY OR DEATH:

Read Operator's Manual (available from dealer) and follow all safety precautions.

Keep all shields in place and in good condition.

Operate mower from tractor seat only.

Lower mower, stop engine and remove key before dismounting tractor.

Allow no children or untrained persons to operate equipment.

Do not transport towed or semi-mounted units over 20 mph.

FAILURE TO OPERATE SAFELY

CAN RESULT IN

INJURY OR DEATH.

18877-C

DANGER

ROTATING BLADES AND

THROWN OBJECTS

Do not put hands or feet under or into mower when engine is running.

Before mowing, clear area of objects that may be thrown by blade.

Keep bystanders away.

Keep guards in place and in good condition.

BLADE CONTACT OR THROWN OBJECTS CAN

CAUSE SERIOUS INJURY OR DEATH.

15503-C

10 - PN 1002940

12 - PN 1004114

AMBER REFLECTOR 9"

 

 

 

 

DANGER

 

11 - PN 57123

 

 

 

If shaft connection is visible, shield

RED REFLECTOR 9"

is missing. Replace shield before

 

 

operating equipment.

1004114

 

 

 

 

12 Safety

MAN0390 (Rev. 6/30/2006)

 

 

Image 12
Contents Rotary Cutter Introduction To the DealerTable of Contents Specifications General InformationDS96 DS120 Free Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishSafety Rules TrainingPreparation Operation TransportationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedKeep Away Be Careful Raised Cutter can Drop and CrushOperation OperationTractor Stability Connect Cutter to Tractor PULL-TYPEConnect Cutter to Tractor Mounted Driveline Attachment Shorten DrivelineCutting Height Adjustment Driveline Interference CheckAttitude Adjustment PULL-TYPE Driveline Adjustment PULL-TYPEWheel Spacing DS120 only Blade SelectionTractor Operation Operating TechniqueCutter Operation Mowing TipsPRE-OPERATION Check List Owners Responsibility Owner Service Owner ServiceBlocking Method LubricationInstalling Blades Servicing BladesRemoving Blades Figure Slip Clutch Assembly Sharpening BladesAdjusting Slip Clutch Rubber Disk ReplacementCleaning Shielding RepairTroubleshooting TroubleshootingDealer Service Dealer ServiceGearbox Maintenance Seal ReplacementVertical Shaft Seal Repair Spindle BOX Horizontal Shaft Seal RepairSpindle Gearbox Repair Remove Gearbox from Cutter Disassemble GearboxReinstall Gearbox Assemble GearboxSpindle Gearbox Assembly Splitter Gearbox Repair Remove Gearbox from Cutter Disassemble Splitter GearboxSide Drive Service Crossbar Removal Crossbar RemovalCrossbar Installation Crossbar TimingJoint Disassembly Joint AssemblyUniversal Joint Repair Install Cups Servicing Tires SafelyAssembly Assembly InstructionsDealer SET-UP Instructions Assemble DS96 PULL-TYPE Cutter Rear HalfInstall Hydraulic Hose DS96 Pull-Type Rear Half InstallationInstall Spring Arm Assemble DS120 PULL-TYPE Cutter Rear HalfDS120 Pull-Type Rear Half Installation DS120 Pull-Type Rear HalfInstall Tongue DS96 & DS120 Cutters Install 3-JOINT DrivelineTongue and Driveline Installation DS96 and DS120 Tongue and Driveline InstallationInstall A-Frame Install Tailwheel ArmsAssemble DS96 Mounted Cutter DS96 Mounted Assembly DS96 Mounted AssemblyInstall Hydraulic Hoses Assemble DS120 Mounted CutterDS120 Mounted Assembly Install Rubber Shielding Fill GearboxesInstall Chain Shielding Optional Optional Chain Shielding InstallationDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List DEALER’S Responsibility Delivery Check List DEALER’S ResponsibilityDealer Check Lists Parts Index PartsDS96 / DS120 Main Frame Assembly DS96 / DS120 Main Frame Parts List DS96Hardware DS96 / DS120 PULL-TYPE ASSEMBLY, Front Half DS96 / DS120 PULL-TYPE ASSEMBLY, Front Half Parts List DS96 PULL-TYPE ASSEMBLY, Rear Half DS120 PULL-TYPE ASSEMBLY, Rear Half DS96 Mounted Assembly DS120 Mounted Assembly DS96 / DS120 Mounted Tailwheel Assembly DS96 / DS120 Splitter Gearbox Assembly DS96 / DS120 Spindle Gearbox Assembly DS96 / DS120 Spindle Gearbox Assembly Parts List DS96 / DS120 Flexible CouplerDS96 / DS120 PULL-TYPE DRIVELINE, Rear 1/3 DS96 / DS120 Slip Clutch Drive Assembly DS120 onlyDS96 / DS120 3-JOINT DRIVE, Front 2/3 Wheel & Tire Assembly DS96 / DS120 Belt Shielding DS96 / DS120 Chain Shielding Optional 8 SINGLE-ACTING Hydraulic Cylinder Hydraulic Cylinder Stroke Control KIT Optional Parking Jack PULL-TYPECrossbar Puller Optional Bolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexSafety Warranty Warranty