Woods Equipment DS96 Install Chain Shielding Optional, Optional Chain Shielding Installation

Page 48

INSTALL CHAIN SHIELDING (OPTIONAL)

The optional chain shielding assemblies are ready for installation when you receive them.

1.Install front and rear chain shielding as shown using self-tapping screws (6), lock washers (7), and flat washers (8).

2.Attach front reflector bracket (9) over left front shield.

Full chain or rubber shielding must be installed when operating in populated areas or other areas where thrown objects could injure people or dam- age property.

•If this machine is not equipped with full chain or rubber shielding, operation must be stopped when anyone comes within 300 feet (92 m).

•This shielding is designed to reduce the risk of thrown objects. The mower deck and protec- tive devices cannot prevent all objects from escaping the blade enclosure in every mowing condition. It is possible for objects to ricochet and escape, traveling as much as 300 feet (92 m).

1. Front chain shield bracket

2. Rear chain shield bracket

3. Front chain pin

4. Rear chain pin

5. 5/16 Chain link

6. Self tapping screw, 3/8 x 1-1/4

7. Lock washer, 3/8

8. Flat washer, 3/8

9. Front reflector bracket

Figure 44. Optional Chain Shielding Installation

48 Assembly	MAN0390 (Rev. 4/6/2007)

Image 48

Contents Rotary Cutter Introduction To the DealerTable of Contents Specifications General InformationDS96 DS120 Free Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishSafety Rules TrainingPreparation Operation TransportationMaintenance Storage Safety & Instructional Decals Replace Immediately If DamagedKeep Away Be Careful Raised Cutter can Drop and CrushOperation OperationTractor Stability Connect Cutter to Tractor PULL-TYPEConnect Cutter to Tractor Mounted Driveline Attachment Shorten DrivelineCutting Height Adjustment Driveline Interference CheckAttitude Adjustment PULL-TYPE Driveline Adjustment PULL-TYPEWheel Spacing DS120 only Blade SelectionTractor Operation Operating TechniqueCutter Operation Mowing TipsPRE-OPERATION Check List Owners Responsibility Owner Service Owner ServiceBlocking Method LubricationInstalling Blades Servicing BladesRemoving Blades Figure Slip Clutch Assembly Sharpening BladesAdjusting Slip Clutch Rubber Disk ReplacementCleaning Shielding RepairTroubleshooting TroubleshootingDealer Service Dealer ServiceGearbox Maintenance Seal ReplacementVertical Shaft Seal Repair Spindle BOX Horizontal Shaft Seal RepairSpindle Gearbox Repair Remove Gearbox from Cutter Disassemble GearboxReinstall Gearbox Assemble GearboxSpindle Gearbox Assembly Splitter Gearbox Repair Remove Gearbox from Cutter Disassemble Splitter GearboxSide Drive Service Crossbar Removal Crossbar RemovalCrossbar Installation Crossbar TimingJoint Disassembly Joint AssemblyUniversal Joint Repair Install Cups Servicing Tires SafelyAssembly Assembly InstructionsDealer SET-UP Instructions Assemble DS96 PULL-TYPE Cutter Rear HalfInstall Hydraulic Hose DS96 Pull-Type Rear Half InstallationInstall Spring Arm Assemble DS120 PULL-TYPE Cutter Rear HalfDS120 Pull-Type Rear Half Installation DS120 Pull-Type Rear HalfInstall Tongue DS96 & DS120 Cutters Install 3-JOINT DrivelineTongue and Driveline Installation DS96 and DS120 Tongue and Driveline InstallationInstall A-Frame Install Tailwheel ArmsAssemble DS96 Mounted Cutter DS96 Mounted Assembly DS96 Mounted AssemblyInstall Hydraulic Hoses Assemble DS120 Mounted CutterDS120 Mounted Assembly Install Rubber Shielding Fill GearboxesInstall Chain Shielding Optional Optional Chain Shielding InstallationDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List DEALER’S Responsibility Delivery Check List DEALER’S ResponsibilityDealer Check Lists Parts Index PartsDS96 / DS120 Main Frame Assembly DS96 / DS120 Main Frame Parts List DS96Hardware DS96 / DS120 PULL-TYPE ASSEMBLY, Front Half DS96 / DS120 PULL-TYPE ASSEMBLY, Front Half Parts List DS96 PULL-TYPE ASSEMBLY, Rear Half DS120 PULL-TYPE ASSEMBLY, Rear Half DS96 Mounted Assembly DS120 Mounted Assembly DS96 / DS120 Mounted Tailwheel Assembly DS96 / DS120 Splitter Gearbox Assembly DS96 / DS120 Spindle Gearbox Assembly DS96 / DS120 Spindle Gearbox Assembly Parts List DS96 / DS120 Flexible CouplerDS96 / DS120 PULL-TYPE DRIVELINE, Rear 1/3 DS96 / DS120 Slip Clutch Drive Assembly DS120 onlyDS96 / DS120 3-JOINT DRIVE, Front 2/3 Wheel & Tire Assembly DS96 / DS120 Belt Shielding DS96 / DS120 Chain Shielding Optional 8 SINGLE-ACTING Hydraulic Cylinder Hydraulic Cylinder Stroke Control KIT Optional Parking Jack PULL-TYPECrossbar Puller Optional Bolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexSafety Warranty Warranty