VERTICAL SHAFT SEAL REPAIR (SPINDLE BOX)
Refer to Figure 19.
1.Disconnect and remove the driveline from the gearbox.
2.Remove vent plug (3) and siphon gear lube from housing through this opening.
3.Remove crossbar (see Crossbar removal on page 33).
4.Remove vertical shaft seal (16). Replace with new seal (see Seal Installation on page 27).
Vertical seal should be recessed in housing. Hori- zontal seal should be pressed flush with outside of housing.
NOTE: Distortion to seal cage or damage to seal lip will cause seal to leak.
5.Fill gearbox with SAE 80W or 90W gear lube until it runs out the level plug.
6.Remove and replace any seal damaged in installation.
HORIZONTAL SHAFT SEAL REPAIR
Refer to Figure 19.
1.Disconnect and remove the driveline from the gearbox.
2.Remove vent plug (3) and siphon gear lube from housing through this opening.
3.If the leak occurred at either end of horizontal shaft (spindle gearbox), remove oil cap (24) and/or oil seal (10). For splitter gearbox (Figure 20) use oil seals (11) and (17). Replace with new one (refer to Seal Installation, page 27).
4.Fill gearbox with SAE 80W or 90W gear lube until it runs out the level plug.
SPINDLE GEARBOX REPAIR
NOTE: Replacing gears, shafts, bearings, and seals may not be cost effective. Purchasing a complete gear- box may be more economical.
REMOVE GEARBOX FROM CUTTER
Refer to Figure 19.
1.Disconnect and remove the driveline from the gearbox.
2.Remove vent plug (3) and siphon gear lube from housing through this opening.
3.Remove cotter pin, washer, and nut from vertical shaft and remove crossbar (see Crossbar removal, page 33).
4.Remove the four bolts that attach gearbox to cutter and remove gearbox. Gearbox is heavy; do not attempt to move without mechanical assistance.
DISASSEMBLE GEARBOX
Refer to Figure 19.
1.Remove 3/8" plug from side of gearbox and pour out gear oil.
2.Remove oil cap (24) (to be replaced).
3.Remove snap ring (9) and shim (5) from input shaft
(11).
4.Support gearbox in hand press and push on input shaft (11) to remove bearing (23).
5.Remove top cover (4) from housing. Remove gear
(6)from inside housing.
6.Remove oil seal (10) from front of housing (to be replaced).
7.Remove snap ring (9) and shim (5) from front of housing (1).
8.Remove input bearing (7) by using a punch and hammer from outside of housing.
9.Support housing in vise in a horizontal position.
10.The castle nut (21), cotter pin (8), and washer (20) are already removed with the stump jumper/crossbar. Remove the protective screen
(17)and seal (16).
11.Remove cotter pin (18), castle nut (12), and washer (25) from output shaft (19).
12.Remove output shaft (19) by using a punch and hammer and tap on top to drive down.
13.Remove gear (5) and shim (15) from inside housing.
14.Remove bearing (15) by using a punch and hammer from the top, outside the housing.
15.Support housing upside down (top cover surface) and remove bearing (15) by using a punch and hammer from the bottom side of the housing.
16.Inspect gears for broken teeth and wear. Some wear is normal and will show on loaded side. Forged gear surfaces are rough when new. Check that wear pattern is smooth.
17.Inspect vertical and horizontal shafts for grooves, nicks, or bumps in the areas where the seals seat. Resurface any damage with emery cloth.
18.Inspect housing and caps for cracks or other damage.
28 Dealer Service | MAN0390 (Rev. 4/6/2007) |
|
|