Conﬁrming Adapter Installation | 3Com EISA 10/100BASE-T specification

2-4 CHAPTER 2: INSTALLING THE HARDWARE

Conﬁrming Adapter Installation

If you are installing the 3C597 EISA adapter in a computer running Windows 95, you can conﬁrm the adapter’s installation by following these steps:

1After starting Windows 95, double-click the My Computer icon.

2Double-click the Control Panel icon.

3Double-click the System icon.

The System Properties box appears, detailing your system setup.

4Click the Device Manager tab.

A list of devices appears, arranged by type.

5Click the Network Adapters tab.

The name of the installed 3Com adapter appears, as shown below:

3Com Fast EtherLink 10/100Mb Bus-Master EISA

Ethernet Adapter

This conﬁrms the adapter’s installation.

6Double-click the adapter’s name to display a description of the adapter and its current status.

The next dialog box conﬁrms that the adapter is working properly.

7Click the Cancel button to leave each dialog box and return to the Control Panel.

For on-line help information about any of the ﬁelds in the display boxes, click the question mark (?) in the upper right corner of the box, move the question mark cursor to the ﬁeld of interest, and click again.

Image 17

3Com EISA 10/100BASE-T manual Conﬁrming Adapter Installation, List of devices appears, arranged by type

Contents

Network Adapter Fast Etherlink Parallel TaskingUser Guide Adapters 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Lifetime Warranty France, Israel Contents Loading Network Drivers Cispr B Compliance Figures Tables Introduction How to Use This GuideAbout this Guide Print Autolink.log Conventions Single-slot, 32-bit half-card Adapter FeaturesIntroduction Procedure Overview Procedures described in this guide are shown in Figure Hardware Installation Overview Installing the Hardware Inserting the Fast EtherLink Eisa Adapter Installing the Boot PromInspecting the Adapter Computer with PCI and Eisa Slots List of devices appears, arranged by type Conﬁrming Adapter InstallationName of the installed 3Com adapter appears, as shown below Connecting to the Network Installing the Hardware Auto Select Media Type Adapter Conﬁguration Overview Configuring the Adapter Conﬁguring the Adapter Using a NOS Other Than Windows Using Windows Complete one of the following instructions Software Option Settings Network Driver Optimization Media TypeFull Duplex Multitasking environments, choosing At the prompt, type Changing the Settings I N N U Press Tab to highlight OK. Press Enter Continue this procedure with any of the other optionsSecond dialog box appears Select Adapter Installed Adapters Drivers Loading Network Locating the Network Drivers Accessing DOS One Eisa Adapter in a Client Describes how to access DOS from various operating systemsLoading NetWare ODI Drivers Loading Network Drivers To view the full text of the license agreement, press F1 Alternatively, at the prompt, type Have only one 3Com Bus Master adapter installed To print the ﬁle, type Multiple Eisa Adapters in a Client When the program has ﬁnished a Save the conﬁguration Main menu appears Reboot the computer Finding the Adapter’s Slot NumberRepeat a for the second adapter One Eisa Adapter in a Server Loading NetWare ODI Drivers Multiple Eisa Adapters in a Server Finding the Adapter’s Port Address for Multiple Adapters For the latest NLMs, contact Novell For NetWare 3.12, 4.0, or To load other types of network drivers, follow these steps Loading Windows 95 DriversLoading Non-NetWare Drivers Ndis Windows for Workgroups Ndis DriversWindows NT, version Windows Additional Drivers Transcend PC Link SmartAgent Driver AgentsDesktop Management Interface Illustrates how the procedures in this chapter might be used Performing Troubleshooting Diagnostic Tests Before Running the Tests Diagnostic Tests Overview Types of Tests Starting the Diagnostic Program Running the Group 1 Tests Command Line AccessTo run the Group 1 tests, follow these steps Press Enter to start the tests Mbps or 100 Mbps Running the Group 3 Test Setting Up an Echo Server Enable the Group 3 test by selecting the Enable Group button Getting Help If a Test Fails To change the test parameters, follow these steps Changing the Test Setup Miscellaneous Checks LED LEDs Performing Troubleshooting and Diagnostic Tests Adapter Card Speciﬁcations SpecificationsCSMA/CD local area network Local area network When properly connected to a 10BASE-T network, RJ-45 Connector Pin AssignmentsCabling Requirements Maximum UTP cable distance is 100 meters at either speed 3Com Bulletin Board Service On-line Technical ServicesAccess by Modem Technical Support World Wide Web Site 3ComFacts Automated Fax ServiceThreeComForum on CompuServe To use ThreeComForum Log on to CompuServe Details about recent conﬁguration changes, if applicable Support from Your Network SupplierLocal numbers are available within the following countries To obtain an RMA number, call or fax Returning Products for Repair AUI cable Glossary Backplane BackboneBus Driver Ethernet Echo serverEMM386 Server Parallel TaskingTransceiver Twisted-pair Numerics SymbolsIndex Diagnostic tests NLMs 4-10, 4-12 NETWARE\SERVER subdirectory 4-11 network Limited Warranty 3Com Corporation Bayfront Plaza Interference Handbook Cispr B Compliance