Alliance Laundry Systems PHM1263R guide

Default Cycles

(continued)

	Cycle Stops	Reclaim	Delicates	90C	60C	40C	90C Perm	60C Perm
	Cycle Stops	Reclaim	Cold	90C	60C	40C	Press	Press
			Cold				Press	Press

	Cycle reference	CY08	CY09	CY10	CY11	CY12	CY13	CY14
	(display in Program Mode)	CY08	CY09	CY10	CY11	CY12	CY13	CY14
	(display in Program Mode)
	Agitation type	18/3/18	10/20/10	18/3/18	18/3/18	18/3/18	18/3/18	18/3/18
	Agitation type	Normal	Gentle	Normal	Normal	Normal	Normal	Normal
		Normal	Gentle	Normal	Normal	Normal	Normal	Normal

	Wash 1 (Wash - ON/OFF)	ON	ON	ON	ON	ON	ON	ON
	Time for agitation (min.)	2	6	2	2	2	2	2
	Fill Temperature	Warm	Cold	Warm	Warm	Warm	Warm	Warm
	Fill Level	High	High	Low	Low	Low	Low	Low
	Supply	OFF	S1	OFF	OFF	OFF	OFF	OFF
	Heat (if enabled)	Yes	Yes	Yes	Yes	Yes	Yes	Yes
	Drain	Yes	Yes	Yes	Yes	Yes	Yes	Yes
	Spin (min.)	0	0	0	0	0	0	0

	Wash 2 (Wash - ON/OFF)	ON	ON	ON	ON	ON	ON	ON
	Time for agitation (min.)	12	2	6	6	6	6	6
	Fill Temperature	Hot	Cold	Hot	Hot	Hot	Hot	Hot
	Fill Level	Low	High	Low	Low	Low	Low	Low
	Supply	S1	OFF	S1, S2	S1, S2	S1, S2	S1, S2	S1, S2
	Heat (if enabled)	Yes	Yes	Yes	Yes	Yes	Yes	Yes
	Drain	Yes	Yes	Yes	Yes	Yes	Yes	Yes
	Spin (min.)	0	0	0	0	0	0	0

	Wash 3 (Wash - ON/OFF)	ON	OFF	OFF	OFF	OFF	OFF	OFF
	Time for agitation (min.)	12	2	2	2	2	2	2
	Fill Temperature	Hot	Cold	Cold	Cold	Cold	Cold	Cold
	Fill Level	High	Low	High	High	High	High	High
	Supply	S2	OFF	OFF	OFF	OFF	OFF	OFF
	Heat (if enabled)	Yes	Yes	Yes	Yes	Yes	Yes	Yes
	Drain	Yes	Yes	Yes	Yes	Yes	Yes	Yes
	Spin (min.)	0	0	0	0	0	0	0

	Wash 4 (Wash - ON/OFF)	OFF	OFF	OFF	OFF	OFF	OFF	OFF
	Time for agitation (min.)	2	2	2	2	2	2	2
	Fill Temperature	Cold	Cold	Cold	Cold	Cold	Cold	Cold
	Fill Level	Low	Low	Low	Low	Low	Low	Low
	Supply	OFF	OFF	OFF	OFF	OFF	OFF	OFF
	Heat (if enabled)	Yes	Yes	Yes	Yes	Yes	Yes	Yes
	Drain	Yes	Yes	Yes	Yes	Yes	Yes	Yes
	Spin (min.)	0	0	0	0	0	0	0

(continued)

F8208801

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

57

Image 59

Alliance Laundry Systems PHM1263R manual Cycle Stops Reclaim Delicates 90C 60C 40C 90C Perm 60C Perm

Contents

Washer-Extractor Page W030 Contents Temperature Controlled Fill Enable/Disable tCF Model Identification Glossary of Terms Power Failure RecoveryPreliminary Information About the Control Select Cycle Pads Refer to Figure Control Identification Four 7-Segment Digits Display IdentificationLight Emitting Diodes LEDs Refer to Figure Washer-Extractor Operation Special Features Manual Programming Entering the Manual ModeHow to Enter the Manual Mode Manual Diagnostics Programmable Options Available Option Description Default Value Range Number DisplayProgramming Control What Can Be Programmed? SUEn FLEnTEnP CoLd/Uarn/Hotor Programming Control Manual Mode Flowchart Manual Programming Flowchart 1 Manual Programming Flowchart 2 Option available on software version 2 only Manual Programming Flowchart 3 Diagnostic Tests Flowchart How to Exit Programming Feature Default Cycle dCYCHow to Program Default Cycle How to Program the Audio Signal Audio Signal AUd Not Cycle Pressed Used How to Read TableMode Card End Key Input Remove Coin ESd Error Code Programming ErrHow to Program Error Code Programming LEr3 SAT FRI Thur WED TUE MON SUN SAT FRI Thur WED TUE MON SUN OFF Final Description Status How to Enter Cycle ProgrammingHow to Program Cycle Agitate AgIt Cycle Programming Cy Fill Step Description Status How to Program Cycle Segment SEg1 Agitate Description Status/Value Step SupplyDescription Status/Value Step Extract Description Programming Drain Step Programming Cycle Time Display How to Program Number of Balance Retries Fahrenheit/Celsius t FC IR Access On/Off IrAHow to Program the IR Access On/Off How to Program Fahrenheit/Celsius How to Program Warm Water Temperature Hot Water Temperature FHWarm Water Temperature FHC How to Program Hot Water Temperature How to Program Cooldown Enable/ Temperature Cold Water Temperature FCCooldown Enable/Temperature Codn How to Program Cold Water Temperature Manual Rapid Advance On/Off rAEn How to Program the Production Test Cycle On/OffHow to Program the Manual Rapid Advance On/Off Production Test Cycle On/Off PtEn Programmable Cycle Time Display PCtd How to Program in the Cycle Time DisplayHow to Program the Programmable Cycle Time Display No Cycle Time Display nCtd How to Program the Pause/Resume Mode Slow Drain Detection Adjust SdAd Set Real-Time Clock rtC-’ How to Program the Time and Date Low Water Level FLo Manual Diagnostics On/Off dAEnHow to Program the Manual Diagnostics On/Off How to Program Low Water Level High Water Level FHI How to Program Medium Water LevelHow to Program High Water Level Medium Water Level FnEd How to Program Temperature Controlled Fill Temperature Controlled Fill Enable/Disable tCF Auto-Water Leak Detection ALd How to Program Auto-Water Leak Detection Collecting Audit Information How to Enter Audit FeatureHow to Read Audit Data How to Exit Audit Feature How to Enter Manual Reset Manual Reset How to Exit Testing Feature Testing Machine Electronic Control FunctionsHow to Enter Testing Feature How to Start Tests Txxx D001D002 D003 Diagnostic Test Descriptions Frame Balance Switch Input Test Temperature Sensor Display TestVAC Switch Input Test VFD Drive Fault Input Test Production Test Cycle Display Test Cycle Step Comments Production Test Cycle Quick Reference Chart DrAI then LoAg thenAg then RAg then Error Codes Door Error Codes How to Exit Rapid Advance Feature Rapid Advance FeatureHow to Use Rapid Advance Infra-red Communications Communications ModeHow to Begin Communications with An External Device Default Cycles Default Cycles Cycle Stops Reclaim Delicates 90C 60C 40C 90C Perm 60C Perm Cycle reference CY08 CY09 Cycle Stops 40C Perm 70C Perm 50C Gentle 30C Gentle Blank CY17 CY18