Washer-Extractor | Alliance Laundry Systems PHM1263R instruction

Washer-Extractor

Refer to Page 4 for Model Numbers

PHM1263R

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

www.comlaundry.com	Part No. F8208801R5
	March 2010

Programming

Image 1

Alliance Laundry Systems PHM1263R manual Washer-Extractor

Contents

Washer-Extractor Page W030 Contents Temperature Controlled Fill Enable/Disable tCF Model Identification Preliminary Information Power Failure RecoveryAbout the Control Glossary of Terms Select Cycle Pads Refer to Figure Control Identification Light Emitting Diodes LEDs Refer to Figure Display IdentificationFour 7-Segment Digits Washer-Extractor Operation Special Features How to Enter the Manual Mode Entering the Manual ModeManual Diagnostics Manual Programming Programming Control Option Description Default Value Range Number DisplayWhat Can Be Programmed? Programmable Options Available TEnP FLEnCoLd/Uarn/Hotor SUEn Programming Control Manual Mode Flowchart Manual Programming Flowchart 1 Manual Programming Flowchart 2 Option available on software version 2 only Manual Programming Flowchart 3 Diagnostic Tests Flowchart How to Program Default Cycle Default Cycle dCYCHow to Exit Programming Feature How to Program the Audio Signal Audio Signal AUd Mode Card End Key Input How to Read TableRemove Coin Not Cycle Pressed Used How to Program Error Code Programming Error Code Programming ErrLEr3 ESd SAT FRI Thur WED TUE MON SUN SAT FRI Thur WED TUE MON SUN OFF How to Program Cycle Agitate AgIt How to Enter Cycle ProgrammingCycle Programming Cy Final Description Status Fill Step Description Status How to Program Cycle Segment SEg1 Description Status/Value SupplyStep Agitate Description Status/Value Step Extract Description Programming Drain Step Programming Cycle Time Display How to Program Number of Balance Retries How to Program the IR Access On/Off IR Access On/Off IrAHow to Program Fahrenheit/Celsius Fahrenheit/Celsius t FC Warm Water Temperature FHC Hot Water Temperature FHHow to Program Hot Water Temperature How to Program Warm Water Temperature Cooldown Enable/Temperature Codn Cold Water Temperature FCHow to Program Cold Water Temperature How to Program Cooldown Enable/ Temperature How to Program the Manual Rapid Advance On/Off How to Program the Production Test Cycle On/OffProduction Test Cycle On/Off PtEn Manual Rapid Advance On/Off rAEn How to Program the Programmable Cycle Time Display How to Program in the Cycle Time DisplayNo Cycle Time Display nCtd Programmable Cycle Time Display PCtd How to Program the Pause/Resume Mode Slow Drain Detection Adjust SdAd Set Real-Time Clock rtC-’ How to Program the Time and Date How to Program the Manual Diagnostics On/Off Manual Diagnostics On/Off dAEnHow to Program Low Water Level Low Water Level FLo How to Program High Water Level How to Program Medium Water LevelMedium Water Level FnEd High Water Level FHI How to Program Temperature Controlled Fill Temperature Controlled Fill Enable/Disable tCF Auto-Water Leak Detection ALd How to Program Auto-Water Leak Detection How to Read Audit Data How to Enter Audit FeatureHow to Exit Audit Feature Collecting Audit Information How to Enter Manual Reset Manual Reset How to Enter Testing Feature Testing Machine Electronic Control FunctionsHow to Start Tests How to Exit Testing Feature D002 D001D003 Txxx Diagnostic Test Descriptions VAC Switch Input Test Temperature Sensor Display TestVFD Drive Fault Input Test Frame Balance Switch Input Test Production Test Cycle Display Test Cycle Step Comments Production Test Cycle Quick Reference Chart Ag then LoAg thenRAg then DrAI then Error Codes Door Error Codes How to Use Rapid Advance Rapid Advance FeatureHow to Exit Rapid Advance Feature How to Begin Communications with An External Device Communications ModeInfra-red Communications Default Cycles Default Cycles Cycle Stops Reclaim Delicates 90C 60C 40C 90C Perm 60C Perm Cycle reference CY08 CY09 Cycle Stops 40C Perm 70C Perm 50C Gentle 30C Gentle Blank CY17 CY18