Communications Mode | Alliance Laundry Systems PHM1263R instruction

Communications Mode

Infra-red Communications

The Infra-red Communications feature allows the control to communicate with an external device. The control can be programmed and have its data read without using the keypad. It may also be used to start and stop various diagnostic tests.

How to Begin Communications with An External Device

The control will go blank and the display will show “-C-” until the communication is complete. If an error occurs that terminates communication, the display will show “EIXX” (“XX” represents the error code).

NOTE: The Infra-red Communications option must be turned on. Refer to option 6 in Programming Control.

54

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F8208801

Image 56

Alliance Laundry Systems PHM1263R manual Communications Mode, Infra-red Communications

Contents

Washer-Extractor Page W030 Contents Temperature Controlled Fill Enable/Disable tCF Model Identification Power Failure Recovery Preliminary InformationAbout the Control Glossary of Terms Control Identification Select Cycle Pads Refer to Figure Four 7-Segment Digits Display IdentificationLight Emitting Diodes LEDs Refer to Figure Washer-Extractor Operation Special Features Entering the Manual Mode How to Enter the Manual ModeManual Diagnostics Manual Programming Option Description Default Value Range Number Display Programming ControlWhat Can Be Programmed? Programmable Options Available FLEn TEnPCoLd/Uarn/Hotor SUEn Programming Control Manual Mode Flowchart Manual Programming Flowchart 1 Manual Programming Flowchart 2 Manual Programming Flowchart 3 Option available on software version 2 only Diagnostic Tests Flowchart How to Exit Programming Feature Default Cycle dCYCHow to Program Default Cycle Audio Signal AUd How to Program the Audio Signal How to Read Table Mode Card End Key InputRemove Coin Not Cycle Pressed Used Error Code Programming Err How to Program Error Code ProgrammingLEr3 ESd SAT FRI Thur WED TUE MON SUN SAT FRI Thur WED TUE MON SUN OFF How to Enter Cycle Programming How to Program Cycle Agitate AgItCycle Programming Cy Final Description Status How to Program Cycle Segment SEg1 Fill Step Description Status Supply Description Status/ValueStep Agitate Description Status/Value Step Programming Drain Step Extract Description How to Program Number of Balance Retries Programming Cycle Time Display IR Access On/Off IrA How to Program the IR Access On/OffHow to Program Fahrenheit/Celsius Fahrenheit/Celsius t FC Hot Water Temperature FH Warm Water Temperature FHCHow to Program Hot Water Temperature How to Program Warm Water Temperature Cold Water Temperature FC Cooldown Enable/Temperature CodnHow to Program Cold Water Temperature How to Program Cooldown Enable/ Temperature How to Program the Production Test Cycle On/Off How to Program the Manual Rapid Advance On/OffProduction Test Cycle On/Off PtEn Manual Rapid Advance On/Off rAEn How to Program in the Cycle Time Display How to Program the Programmable Cycle Time DisplayNo Cycle Time Display nCtd Programmable Cycle Time Display PCtd Slow Drain Detection Adjust SdAd How to Program the Pause/Resume Mode How to Program the Time and Date Set Real-Time Clock rtC-’ Manual Diagnostics On/Off dAEn How to Program the Manual Diagnostics On/OffHow to Program Low Water Level Low Water Level FLo How to Program Medium Water Level How to Program High Water LevelMedium Water Level FnEd High Water Level FHI Temperature Controlled Fill Enable/Disable tCF How to Program Temperature Controlled Fill How to Program Auto-Water Leak Detection Auto-Water Leak Detection ALd How to Enter Audit Feature How to Read Audit DataHow to Exit Audit Feature Collecting Audit Information Manual Reset How to Enter Manual Reset Testing Machine Electronic Control Functions How to Enter Testing FeatureHow to Start Tests How to Exit Testing Feature D001 D002D003 Txxx Diagnostic Test Descriptions Temperature Sensor Display Test VAC Switch Input TestVFD Drive Fault Input Test Frame Balance Switch Input Test Production Test Cycle Production Test Cycle Quick Reference Chart Display Test Cycle Step Comments LoAg then Ag thenRAg then DrAI then Error Codes Error Codes Door How to Exit Rapid Advance Feature Rapid Advance FeatureHow to Use Rapid Advance Infra-red Communications Communications ModeHow to Begin Communications with An External Device Default Cycles Default Cycles Cycle Stops Reclaim Delicates 90C 60C 40C 90C Perm 60C Perm Cycle reference CY08 CY09 Cycle Stops 40C Perm 70C Perm 50C Gentle 30C Gentle Blank CY17 CY18